REVISION AP
HLE-1XX-02-XXX-DV-XX-XX-XX
OPTION
-TR: TAPE & REEL
No OF POSITIONS
-02 THRU -50
(PER ROW)
DO NOT
SCALE FROM
THIS PRINT
(2 - 29 POSITIONS ONLY)
FIG 5
OPTION
-P: PICK & PLACE PAD
-BE OPTION
LEAD STYLE
(POS -03 THRU -50 ONLY)
-A: ALIGNMENT PIN (4 POS MIN)
-LC: LOCKING CLIP (2 POS MIN)
(SEE NOTE 9)
(SAME AS FIG 1 UNLESS OTHERWISE STATED)
RHLE-50-DBE
-02: SURFACE MOUNT
(USE C-132-12-X)
C
PLATING SPECIFICATION
-K: POLYAMIDE FILM PAD (AVAILABLE
ON POS -03 THRU -50; .005 [.13]
THICKNESS WITH SILICONE ADHESIVE)
(SEE FIG 4)
+.008 [.20]
-.005 [.13]
No OF POS x .100 [2.54]
-G: 20µ" GOLD IN CONTACT AREA
3µ" ON TAIL (USE C-132-12-G)
-S: 30µ" SELECTIVE GOLD IN CONTACT
AREA MATTE TIN ON TAIL
(USE C-132-12-S)
({No of POS - 1} x .100 [2.54])
.005 [.13]
-F: 3µ" SELECTIVE FLASH GOLD IN CONTACT
AREA MATTE TIN ON TAIL
OPTION
.100 2.54
REF
(USE C-132-12-F)
-BE: BOTTOM ENTRY
(USE RHLE-50-DBE)(SEE FIG. 5)
(LEAVE BLANK FOR STANDARD)
02
-L: 10µ" SELECTIVE LIGHT GOLD IN
CONTACT AREA MATTE TIN ON TAIL
(USE C-132-12-L)
.200 5.08
REF
-H: 30µ" HEAVY GOLD IN CONTACT AREA
3µ" ON TAIL (USE C-132-12-H)
-STL: 30µ" SELECTIVE GOLD IN CONTACT
AREA TIN/LEAD (90%/10 +/-5%)
(USE C-132-12-STL)
01
ROW SPECIFICATION
-SM: 30µ" SELECTIVE GOLD IN CONTACT
AREA MATTE TIN ON TAIL
(USE C-132-12-S)
-FM: 3µ" SELECTIVE FLASH GOLD IN CONTACT
AREA MATTE TIN ON TAIL (USE C-132-12-F)
-LM: 10µ" LIGHT GOLD IN CONTACT AREA
MATTE TIN ON TAIL (USE C-132-12-L)
-DV: DOUBLE VERTICAL
(USE RHLE-50-D)
2
MAX SWAY
(EITHER DIRECTION)
C-132-12-XXX
.020 0.51 REF
PATENT NUMBERS
5713755 / 5961339
RHLE-50-D
.259 6.58 REF
SEE NOTE 10
"A"
90°±3°
C
C
.144 3.66
SEE TABLE 2
SECTION "A"-"A"
"A"
NOTES:
FIG 1
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN .002 [.05]
OFF THE SURFACE OF THE PART.
HLE-116-02-XXX-DV SHOWN
3. PULL OUT FORCE FOR -LC, -A, & CONTACT IS 12 oz MIN.
4. COPLANARITY: SEE TABLE 2.
5. BURR ALLOWANCE: .003 [.08] MAX
6. CUT ASSEMBLIES AFTER FILL. CUT FLASH TO BE .010 MAX WITH NO FLASH
ALLOWED IN HOLES OR EXTENDING BELOW LEADS. WILL LOSE A POSITION
FOR EVERY CUT MADE ON A SOCKET STRIP.
FIG 2
-A & -LC OPTION
7. TUBE POSITIONS 03 THRU 50. LAYER PACKAGE POSITION 02.
8. ENDWALL THICKNESS: .030+/-.005[.76+/-.13] TO BE MEASURED FROM BOTTOM VIEW.
9. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE –LC OPTION IS NOT
COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS MANUAL PLACEMENT
FOR ALL ASSEMBLIES WITH THE –LC OPTION.
.050 1.27
C
(No OF POS -2) x.1000 [2.540]
10. SAMTEC LOGO MAY NOT BE PRESENT ON CUT TO POSITION CONNECTORS.
C
.050 1.27
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
.XX: .01 [.3]
3
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
SM-A10H
.0625 1.588
.XXX: .005 [.13]
.008 x .056 REF
[.20 x 1.42]
LC-08-TM-01
.XXXX: .0020 [.051]
MATERIAL:
SHEET SCALE: 2:1
DO NOT SCALE DRAWING
DESCRIPTION:
[2.54] .100 TIGER BEAM SOCKET ASSEMBLY
DWG. NO.
3
MAX SWAY
BODY: VECTRA E130i
CONTACT: BeCu
(EITHER DIRECTION)
3
MAX SWAY
(EITHER DIRECTION)
HLE-1XX-02-XXX-DV-XX-XX-XX
F:\DWG\MISC\MKTG\HLE-1XX-02-XXX-DV-XX-XX-XX-MKT.SLDDRW
ED MESSER 12/19/98
SHEET 1 OF 2
BY:
QQ：528164397 复制
