LM158AH现货热卖使用介绍供应商报价哪里找芯片批发报价-中国IC网-芯三七

当前位置：IC37首页_>L字母起始型号索引_>L字母起始型号索引第458页更新时间：2024-12-04 17:21:15

产品型号LM158AH的概述

LM158AH芯片概述 LM158AH是一款广泛应用的双运算放大器，属于LM158系列。该芯片由国家半导体公司（National Semiconductor）推出，广泛应用于各种模拟电路设计中。LM158AH集成了两个高增益差分放大器，其输出能够驱动负载电流，适用于多种电路配置。由于其优越的性能和高性价比，LM158AH被广泛应用于音频处理、信号调理和传感器应用等场合。运算放大器的特点在于其高增益、高输入阻抗、低输出阻抗以及优秀的线性度，使它们适用于加法器、减法器、比较器、滤波器等多种功能模组。LM158AH的电源电压范围较宽，从双极性电源±1.5V到±15V都能够正常工作。此外，该芯片支持单电源供电，这进一步拓宽了其应用范围。 LM158AH的详细参数 LM158AH的关键电气特性如下： 1. 工作电源电压: 双电源：±1.5V至±15V，单电源：3V至30V 2. 增益带宽积: ...

产品型号LM158AH的Datasheet PDF文件预览

October 2005

LM158/LM258/LM358/LM2904

Low Power Dual Operational Amplifiers

General Description

Advantages

n Two internally compensated op amps

n Eliminates need for dual supplies

The LM158 series consists of two independent, high gain,

internally frequency compensated operational amplifiers

which were designed specifically to operate from a single

power supply over a wide range of voltages. Operation from

split power supplies is also possible and the low power

supply current drain is independent of the magnitude of the

power supply voltage.

n Allows direct sensing near GND and V_OUTalso goes to

GND

n Compatible with all forms of logic

n Power drain suitable for battery operation

Application areas include transducer amplifiers, dc gain

blocks and all the conventional op amp circuits which now

can be more easily implemented in single power supply

systems. For example, the LM158 series can be directly

operated off of the standard +5V power supply voltage which

is used in digital systems and will easily provide the required

interface electronics without requiring the additional 15V

power supplies.

Features

n Available in 8-Bump micro SMD chip sized package,

(See AN-1112)

n Internally frequency compensated for unity gain

n Large dc voltage gain: 100 dB

n Wide bandwidth (unity gain): 1 MHz

(temperature compensated)

n Wide power supply range:

— Single supply: 3V to 32V

The LM358 and LM2904 are available in a chip sized pack-

age (8-Bump micro SMD) using National’s micro SMD pack-

age technology.

— or dual supplies:

1.5V to 16V

n Very low supply current drain (500 µA)—essentially

independent of supply voltage

n Low input offset voltage: 2 mV

n Input common-mode voltage range includes ground

n Differential input voltage range equal to the power

supply voltage

Unique Characteristics

n In the linear mode the input common-mode voltage

range includes ground and the output voltage can also

swing to ground, even though operated from only a

single power supply voltage.

n Large output voltage swing

n The unity gain cross frequency is temperature

compensated.

n The input bias current is also temperature compensated.

Voltage Controlled Oscillator (VCO)

00778723

DS007787

www.national.com

Distributors for availability and specifications.

Absolute Maximum Ratings (Note 9)

If Military/Aerospace specified devices are required,

please contact the National Semiconductor Sales Office/

LM158/LM258/LM358

LM2904

LM158A/LM258A/LM358A

Supply Voltage, V⁺

Differential Input Voltage

Input Voltage

32V

26V

−0.3V to +32V

−0.3V to +26V

Power Dissipation (Note 1)

Molded DIP

830 mW

550 mW

530 mW

435mW

830 mW

530 mW

Metal Can

Small Outline Package (M)

micro SMD

Output Short-Circuit to GND

(One Amplifier) (Note 2)

V⁺≤ 15V and T_A= 25˚C

Continuous

50 mA

Continuous

50 mA

Input Current (V_IN−0.3V) (Note 3)

Operating Temperature Range

LM358

0˚C to +70˚C

−25˚C to +85˚C

−55˚C to +125˚C

−65˚C to +150˚C

−40˚C to +85˚C

LM258

LM158

Storage Temperature Range

Lead Temperature, DIP

(Soldering, 10 seconds)

Lead Temperature, Metal Can

(Soldering, 10 seconds)

Soldering Information

Dual-In-Line Package

Soldering (10 seconds)

Small Outline Package

Vapor Phase (60 seconds)

Infrared (15 seconds)

−65˚C to +150˚C

260˚C

300˚C

260˚C

215˚C

220˚C

215˚C

220˚C

See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering

surface mount devices.

ESD Tolerance (Note 10)

250V

Electrical Characteristics

V⁺= +5.0V, unless otherwise stated

Parameter

Conditions

LM158A

LM358A

LM158/LM258

Units

Min Typ Max Min Typ Max Min Typ Max

Input Offset Voltage

Input Bias Current

(Note 5), T_A= 25˚C

I_IN(+)or I_IN(−), T_A= 25˚C,

V_CM= 0V, (Note 6)

100

150

Input Offset Current

Input Common-Mode

Voltage Range

I_IN(+)− I_IN(−), V_CM= 0V, T_A= 25˚C

V⁺= 30V, (Note 7)

(LM2904, V⁺= 26V), T_A= 25˚C

V⁺−1.5

Supply Current

Over Full Temperature Range

∞

on All Op Amps

R_L

V⁺= 30V (LM2904 V⁺= 26V)

V⁺= 5V

0.5

1.2

0.5

1.2

0.5

1.2

www.national.com

Electrical Characteristics

V⁺= +5.0V, unless otherwise stated

Parameter

Conditions

LM358

Typ

LM2904

Units

Min

Max

Min

Typ

Max

Input Offset Voltage

Input Bias Current

(Note 5) , T_A= 25˚C

I_IN(+)or I_IN(−), T_A= 25˚C,

V_CM= 0V, (Note 6)

250

Input Offset Current

Input Common-Mode

Voltage Range

I_IN(+)− I_IN(−), V_CM= 0V, T_A= 25˚C

V⁺= 30V, (Note 7)

(LM2904, V⁺= 26V), T_A= 25˚C

V⁺−1.5

Supply Current

Over Full Temperature Range

∞

on All Op Amps

R_L

V⁺= 30V (LM2904 V⁺= 26V)

V⁺= 5V

0.5

1.2

0.5

1.2

Electrical Characteristics

V⁺= +5.0V, (Note 4), unless otherwise stated

LM158A

LM358A

LM158/LM258

Units

Parameter

Conditions

Min Typ Max Min Typ Max Min Typ Max

Large Signal Voltage

Gain

V⁺= 15V, T_A= 25˚C,

R_L≥ 2 kΩ, (For V_O= 1V

to 11V)

50 100 25 100 50 100

V/mV

Common-Mode

Rejection Ratio

Power Supply

Rejection Ratio

T_A= 25˚C,

V_CM= 0V to V⁺−1.5V

V⁺= 5V to 30V

(LM2904, V⁺= 5V

to 26V), T_A= 25˚C

f = 1 kHz to 20 kHz, T_A= 25˚C

65 100

−120

65 100

−120

65 100

−120

Amplifier-to-Amplifier

Coupling

(Input Referred), (Note 8)

Output Current

Source V_IN= 1V,

−

V_IN= 0V,

V⁺= 15V,

µA

V_O= 2V, T_A= 25˚C

−

Sink V_IN= 1V, V_IN= 0V

V⁺= 15V, T_A= 25˚C,

V_O= 2V

−

V_IN= 1V,

V_IN= 0V

T_A= 25˚C, V_O= 200 mV,

V⁺= 15V

Short Circuit to Ground

T_A= 25˚C, (Note 2),

V⁺= 15V

Input Offset Voltage

Drift

(Note 5)

R_S= 0Ω

µV/˚C

Input Offset Current

Drift

I_IN(+)− I_IN(−)

100

R_S= 0Ω

200

100

V⁺−2

300

200

V⁺−2

pA/˚C

Input Bias Current

Input Common-Mode

Voltage Range

I_IN(+)or I_IN(−)

300

V⁺= 30 V, (Note 7)

(LM2904, V⁺= 26V)

V⁺−2

www.national.com

Electrical Characteristics (Continued)

V⁺= +5.0V, (Note 4), unless otherwise stated

LM158A

LM358A

LM158/LM258

Units

Parameter

Conditions

Min Typ Max Min Typ Max Min Typ Max

Large Signal Voltage

Gain

V⁺= +15V

(V_O= 1V to 11V)

V/mV

R_L≥ 2 kΩ

Output

Voltage

Swing

V_OHV⁺= +30V

R_L= 2 kΩ

(LM2904, V⁺= 26V) R_L= 10 kΩ

V_OLV⁺= 5V, R_L= 10 kΩ

−

Output Current

Source V_IN= +1V, V_IN= 0V,

V⁺= 15V, V_O= 2V

−

Sink V_IN= +1V, V_IN= 0V,

V⁺= 15V, V_O= 2V

Electrical Characteristics

V⁺= +5.0V, (Note 4), unless otherwise stated

LM358

Typ

LM2904

Typ

Units

Parameter

Conditions

Min

Max

Min

Max

Large Signal Voltage

Gain

V⁺= 15V, T_A= 25˚C,

R_L≥ 2 kΩ, (For V_O= 1V

to 11V)

100

V/mV

Common-Mode

Rejection Ratio

Power Supply

Rejection Ratio

T_A= 25˚C,

V_CM= 0V to V⁺−1.5V

V⁺= 5V to 30V

(LM2904, V⁺= 5V

to 26V), T_A= 25˚C

f = 1 kHz to 20 kHz, T_A= 25˚C

100

−120

100

−120

Amplifier-to-Amplifier

Coupling

(Input Referred), (Note 8)

Output Current

Source V_IN= 1V,

−

V_IN= 0V,

V⁺= 15V,

µA

V_O= 2V, T_A= 25˚C

−

Sink V_IN= 1V, V_IN= 0V

V⁺= 15V, T_A= 25˚C,

V_O= 2V

−

V_IN= 1V,

V_IN= 0V

T_A= 25˚C, V_O= 200 mV,

V⁺= 15V

Short Circuit to Ground

T_A= 25˚C, (Note 2),

V⁺= 15V

Input Offset Voltage

Drift

(Note 5)

R_S= 0Ω

µV/˚C

Input Offset Current

Drift

I_IN(+)− I_IN(−)

150

200

R_S= 0Ω

pA/˚C

Input Bias Current

Input Common-Mode

Voltage Range

I_IN(+)or I_IN(−)

500

V⁺= 30 V, (Note 7)

(LM2904, V⁺= 26V)

V⁺−2

www.national.com

Electrical Characteristics (Continued)

V⁺= +5.0V, (Note 4), unless otherwise stated

LM358

Typ

LM2904

Typ

Units

Parameter

Conditions

Min

Max

Min

Max

Large Signal Voltage

Gain

V⁺= +15V

(V_O= 1V to 11V)

V/mV

R_L≥ 2 kΩ

Output

V_OHV⁺= +30V

R_L= 2 kΩ

Voltage

(LM2904, V⁺= 26V)

R_L= 10 kΩ

Swing

V_OLV⁺= 5V, R_L= 10 kΩ

100

−

Output Current

Source V_IN= +1V, V_IN= 0V,

V⁺= 15V, V_O= 2V

−

Sink V_IN= +1V, V_IN= 0V,

V⁺= 15V, V_O= 2V

Note 1: For operating at high temperatures, the LM358/LM358A, LM2904 must be derated based on a +125˚C maximum junction temperature and a thermal

resistance of 120˚C/W for MDIP, 182˚C/W for Metal Can, 189˚C/W for Small Outline package, and 230˚C/W for micro SMD, which applies for the device soldered

in a printed circuit board, operating in a still air ambient. The LM258/LM258A and LM158/LM158A can be derated based on a +150˚C maximum junction temperature.

The dissipation is the total of both amplifiers — use external resistors, where possible, to allow the amplifier to saturate or to reduce the power which is dissipated

in the integrated circuit.

Note 2: Short circuits from the output to V can cause excessive heating and eventual destruction. When considering short cirucits to ground, the maximum output

current is approximately 40 mA independent of the magnitude of V . At values of supply voltage in excess of +15V, continuous short-circuits can exceed the power

dissipation ratings and cause eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers.

Note 3: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP

transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action

on the IC chip. This transistor action can cause the output voltages of the op amps to go to the V voltage level (or to ground for a large overdrive) for the time duration

that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value

greater than −0.3V (at 25˚C).

Note 4: These specifications are limited to −55˚C ≤ T ≤ +125˚C for the LM158/LM158A. With the LM258/LM258A, all temperature specifications are limited to

−25˚C ≤ T ≤ +85˚C, the LM358/LM358A temperature specifications are limited to 0˚C ≤ T ≤ +70˚C, and the LM2904 specifications are limited to −40˚C ≤ T ≤

+85˚C.

Note 5: V . 1.4V, R = 0Ω with V from 5V to 30V; and over the full input common-mode range (0V to V −1.5V) at 25˚C. For LM2904, V from 5V to 26V.

Note 6: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so

no loading change exists on the input lines.

Note 7: The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25˚C). The upper end of the

common-mode voltage range is V −1.5V (at 25˚C), but either or both inputs can go to +32V without damage (+26V for LM2904), independent of the magnitude of

V .

Note 8: Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This typically can be

detected as this type of capacitance increases at higher frequencies.

Note 9: Refer to RETS158AX for LM158A military specifications and to RETS158X for LM158 military specifications.

Note 10: Human body model, 1.5 kΩ in series with 100 pF.

www.national.com

Typical Performance Characteristics

Input Voltage Range

Input Current

00778734

00778735

Supply Current

Voltage Gain

00778736

00778737

Open Loop Frequency Response

Common-Mode Rejection Ratio

00778738

00778739

www.national.com

Typical Performance Characteristics (Continued)

Voltage Follower Pulse Response

Voltage Follower Pulse Response (Small Signal)

00778741

00778740

Large Signal Frequency Response

Output Characteristics Current Sourcing

00778742

00778743

Output Characteristics Current Sinking

Current Limiting

00778744

00778745

www.national.com

Typical Performance Characteristics (Continued)

Input Current (LM2902 only)

Voltage Gain (LM2902 only)

00778746

00778747

Application Hints

The LM158 series are op amps which operate with only a

single power supply voltage, have true-differential inputs,

and remain in the linear mode with an input common-mode

voltage of 0 V_DC. These amplifiers operate over a wide range

of power supply voltage with little change in performance

characteristics. At 25˚C amplifier operation is possible down

Capacitive loads which are applied directly to the output of

the amplifier reduce the loop stability margin. Values of 50

pF can be accomodated using the worst-case non-inverting

unity gain connection. Large closed loop gains or resistive

isolation should be used if larger load capacitance must be

driven by the amplifier.

to a minimum supply voltage of 2.3 V_DC

The bias network of the LM158 establishes a drain current

which is independent of the magnitude of the power supply

Precautions should be taken to insure that the power supply

for the integrated circuit never becomes reversed in polarity

or that the unit is not inadvertently installed backwards in a

test socket as an unlimited current surge through the result-

ing forward diode within the IC could cause fusing of the

internal conductors and result in a destroyed unit.

voltage over the range of 3 V_DCto 30 V_DC

Output short circuits either to ground or to the positive power

supply should be of short time duration. Units can be de-

stroyed, not as a result of the short circuit current causing

metal fusing, but rather due to the large increase in IC chip

dissipation which will cause eventual failure due to exces-

sive function temperatures. Putting direct short-circuits on

more than one amplifier at a time will increase the total IC

power dissipation to destructive levels, if not properly pro-

tected with external dissipation limiting resistors in series

with the output leads of the amplifiers. The larger value of

output source current which is available at 25˚C provides a

larger output current capability at elevated temperatures

(see typical performance characteristics) than a standard IC

op amp.

Large differential input voltages can be easily accomodated

and, as input differential voltage protection diodes are not

needed, no large input currents result from large differential

input voltages. The differential input voltage may be larger

than V⁺without damaging the device. Protection should be

provided to prevent the input voltages from going negative

more than −0.3 V_DC(at 25˚C). An input clamp diode with a

resistor to the IC input terminal can be used.

To reduce the power supply current drain, the amplifiers

have a class A output stage for small signal levels which

converts to class B in a large signal mode. This allows the

amplifiers to both source and sink large output currents.

Therefore both NPN and PNP external current boost transis-

tors can be used to extend the power capability of the basic

amplifiers. The output voltage needs to raise approximately

1 diode drop above ground to bias the on-chip vertical PNP

transistor for output current sinking applications.

The circuits presented in the section on typical applications

emphasize operation on only a single power supply voltage.

If complementary power supplies are available, all of the

standard op amp circuits can be used. In general, introduc-

ing a pseudo-ground (a bias voltage reference of V⁺/2) will

allow operation above and below this value in single power

supply systems. Many application circuits are shown which

take advantage of the wide input common-mode voltage

range which includes ground. In most cases, input biasing is

not required and input voltages which range to ground can

easily be accommodated.

For ac applications, where the load is capacitively coupled to

the output of the amplifier, a resistor should be used, from

the output of the amplifier to ground to increase the class A

bias current and prevent crossover distortion. Where the

load is directly coupled, as in dc applications, there is no

crossover distortion.

www.national.com

Connection Diagrams

DIP/SO Package

Metal Can Package

00778701

00778702

Top View

8-Bump micro SMD

00778755

Top View

(Bump Side Down)

LM358BP micro SMD Marking Orientation

LM2904IBP micro SMD Marking Orientation

00778757

00778756

Top View

LM358TP micro SMD Marking Orientation

LM2904ITP micro SMD Marking Orientation

00778758

00778759

Top View

www.national.com

Ordering Information

Temperature Range

Package

NSC Drawing

M08A

−55˚C to 125˚C

−25˚C to 85˚C

0˚C to 70˚C

LM358AM

LM358AMX

LM358M

−40˚C to 85˚C

LM2904M

SO-8

LM2904MX

LM358MX

LM358AN

LM358N

8-Pin Molded DIP

8-Pin Ceramic DIP

LM2904N

N08E

LM158AJ/883(Note 11)

LM158J/883(Note 11)

LM158J

J08A

LM158AJLQML(Note 12)

LM158AJQMLV(Note 12)

LM158AH/883(Note 11)

LM158H/883(Note 11)

LM158AH

TO-5, 8-Pin Metal

Can

LM258H

LM358H

H08C

LM158H

LM158AHLQML(Note 12)

LM158AHLQMLV(Note 12)

8-Bump micro

SMD

LM358BP

LM358BPX

LM358TP

LM2904IBP

LM2904IBPX

LM2904ITP

LM2904ITPX

BPA08AAB

0.85 mm Thick

8-Bump micro

SMD

TPA08AAA

LM358TPX

0.50 mm Thick

Lead Free

14-Pin Ceramic

SOIC

LM158AWG/883

WG10A

Note 11: LM158 is available per SMD #5962-8771001

LM158A is available per SMD #5962-8771002

Note 12: See STD Mil DWG 5962L87710 for Radiation Tolerant Devices

www.national.com

Typical Single-Supply Applications

(V⁺= 5.0 V_DC

Non-Inverting DC Gain (0V Output)

)

00778706

00778707

R not needed due to temperature independent I

DC Summing Amplifier

(V_IN’S≥ 0 V_DCand V_O≥ 0 V_DC

)

Power Amplifier

00778709

00778708

= 0 V

for V = 0 V

DC IN DC

Where: V = V + V − V − V

= 10

(V + V ) ≥ (V + V ) to keep V

0 V

www.national.com

Typical Single-Supply Applications (V⁺= 5.0 V_DC) (Continued)

“BI-QUAD” RC Active Bandpass Filter

00778710

= 1 kHz

Q = 50

= 100 (40 dB)

Fixed Current Sources

Lamp Driver

00778712

00778711

www.national.com

Typical Single-Supply Applications (V⁺= 5.0 V_DC) (Continued)

LED Driver

Current Monitor

00778713

00778714

(Increase R1 for I small)

≤ V −2V

Driving TTL

Voltage Follower

00778715

00778717

= V

Pulse Generator

00778716

www.national.com

Typical Single-Supply Applications (V⁺= 5.0 V_DC) (Continued)

Squarewave Oscillator

Pulse Generator

00778718

00778719

Low Drift Peak Detector

00778720

HIGH Z

LOW Z

OUT

www.national.com

Typical Single-Supply Applications (V⁺= 5.0 V_DC) (Continued)

High Compliance Current Sink

Comparator with Hysteresis

00778722

00778721

= 1 amp/volt V

(Increase R for I small)

Voltage Controlled Oscillator (VCO)

00778723

WIDE CONTROL VOLTAGE RANGE: 0 V

≤ V ≤ 2 (V −1.5V

)

www.national.com

Typical Single-Supply Applications (V⁺= 5.0 V_DC) (Continued)

AC Coupled Inverting Amplifier

00778724

Ground Referencing a Differential Input Signal

00778725

www.national.com

Typical Single-Supply Applications (V⁺= 5.0 V_DC) (Continued)

AC Coupled Non-Inverting Amplifier

00778726

= 11 (As Shown)

DC Coupled Low-Pass RC Active Filter

00778727

= 1 kHz

Q = 1

= 2

www.national.com

Typical Single-Supply Applications (V⁺= 5.0 V_DC) (Continued)

Bandpass Active Filter

00778728

= 1 kHz

Q = 25

High Input Z, DC Differential Amplifier

00778729

www.national.com

Typical Single-Supply Applications (V⁺= 5.0 V_DC) (Continued)

Photo Voltaic-Cell Amplifier

Bridge Current Amplifier

00778730

00778733

High Input Z Adjustable-Gain

DC Instrumentation Amplifier

00778731

www.national.com

Typical Single-Supply Applications (V⁺= 5.0 V_DC) (Continued)

Using Symmetrical Amplifiers to

Reduce Input Current (General Concept)

00778732

Schematic Diagram (Each Amplifier)

00778703

www.national.com

Physical Dimensions inches (millimeters) unless otherwise noted

Metal Can Package (H)

NS Package Number H08C

Cerdip Package (J)

NS Package Number J08A

www.national.com

Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

SOIC Package (M)

NS Package Number M08A

Molded Dip Package (N)

NS Package Number N08E

www.national.com

Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

Order Number LM158AWG/883

NS Package Number WG10A

www.national.com

Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

NOTES: UNLESS OTHERWISE SPECIFIED

1. EPOXY COATING

2. 63Sn/37Pb EUTECTIC BUMP

3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD.

4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION REMAINING PINS ARE NUMBERED

COUNTERCLOCKWISE.

5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X IS PACKAGE WIDTH, X IS PACKAGE LENGTH AND X IS

PACKAGE HEIGHT.

6. REFERENCE JEDEC REGISTRATION MO-211, VARIATION BC.

8-Bump micro SMD

NS Package Number BPA08AAB

X₁= 1.285 X₂= 1.285 X₃= 0.850

www.national.com

Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

NOTES: UNLESS OTHERWISE SPECIFIED

1. EPOXY COATING

2. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD.

3. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION REMAINING PINS ARE NUMBERED

COUNTERCLOCKWISE.

4. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X IS PACKAGE WIDTH, X IS PACKAGE LENGTH AND X IS

PACKAGE HEIGHT.

5. REFERENCE JEDEC REGISTRATION MO-211, VARIATION BC.

8-Bump micro SMD Lead Free

NS Package Number TPA08AAA

X₁= 1.285 X₂= 1.285 X₃= 0.500

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves

the right at any time without notice to change said circuitry and specifications.

For the most current product information visit us at www.national.com.

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS

WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR

CORPORATION. As used herein:

1. Life support devices or systems are devices or systems

which, (a) are intended for surgical implant into the body, or

(b) support or sustain life, and whose failure to perform when

properly used in accordance with instructions for use

provided in the labeling, can be reasonably expected to result

in a significant injury to the user.

2. A critical component is any component of a life support

device or system whose failure to perform can be reasonably

expected to cause the failure of the life support device or

system, or to affect its safety or effectiveness.

BANNED SUBSTANCE COMPLIANCE

National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products

Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain

no ‘‘Banned Substances’’ as defined in CSP-9-111S2.

Leadfree products are RoHS compliant.

National Semiconductor

Americas Customer

Support Center

National Semiconductor

Europe Customer Support Center

Fax: +49 (0) 180-530 85 86

National Semiconductor

Asia Pacific Customer

Support Center

National Semiconductor

Japan Customer Support Center

Fax: 81-3-5639-7507

Email: new.feedback@nsc.com

Tel: 1-800-272-9959

Email: europe.support@nsc.com

Deutsch Tel: +49 (0) 69 9508 6208

English Tel: +44 (0) 870 24 0 2171

Français Tel: +33 (0) 1 41 91 8790

Email: ap.support@nsc.com

Email: jpn.feedback@nsc.com

Tel: 81-3-5639-7560

www.national.com

LM158AH相关文章

配单直通车

深圳市芯福林电子有限公司服务专线: 13418564337 在线联系:

QQ：2881495808 复制

QQ：308365177 复制

深圳市中利达电子科技有限公司服务专线: 0755-13686833545 在线联系:

QQ：1902134819 复制

QQ：2881689472 复制

首天国际（深圳）科技有限公司服务专线: 0755-82807802/82807803 在线联系:

QQ：528164397 复制

QQ：1318502189 复制

北京元坤伟业科技有限公司服务专线: 010-62104931621064316210489162104791 在线联系:

QQ：857273081 复制

QQ：1594462451 复制

柒号芯城电子商务（深圳）有限公司服务专线: 18922803401 在线联系:

QQ：2881677436 复制

QQ：2881620402 复制

LM158AH产品参数

型号:	LM158AH
是否无铅：	含铅
是否Rohs认证：	不符合
生命周期：	Obsolete
IHS 制造商：	STMICROELECTRONICS
零件包装代码：	TO-99
包装说明：	METAL CAN, TO-99, 8 PIN
针数：	8
Reach Compliance Code：	not_compliant
ECCN代码：	EAR99
HTS代码：	8542.33.00.01
风险等级：	5.03
Is Samacsys：	N
放大器类型：	OPERATIONAL AMPLIFIER
架构：	VOLTAGE-FEEDBACK
最大平均偏置电流 (IIB)：	0.1 µA
25C 时的最大偏置电流 (IIB)：	0.05 µA
标称共模抑制比：	60 dB
频率补偿：	YES
最大输入失调电压：	4000 µV
JESD-30 代码：	O-MBCY-W8
JESD-609代码：	e0
低-失调：	NO
标称负供电电压 (Vsup)：
功能数量：	2
端子数量：	8
最高工作温度：	125 °C
最低工作温度：	-55 °C
封装主体材料：	METAL
封装代码：	TO-99
封装等效代码：	CAN8,.2
封装形状：	ROUND
封装形式：	CYLINDRICAL
峰值回流温度（摄氏度）：	NOT SPECIFIED
电源：	+-1.5/+-15/3/30 V
认证状态：	Not Qualified
最小摆率：	0.3 V/us
标称压摆率：	0.6 V/us
子类别：	Operational Amplifier
最大压摆率：	2 mA
供电电压上限：	32 V
标称供电电压 (Vsup)：	5 V
表面贴装：	NO
技术：	BIPOLAR
温度等级：	MILITARY
端子面层：	Tin/Lead (Sn/Pb)
端子形式：	WIRE
端子位置：	BOTTOM
处于峰值回流温度下的最长时间：	NOT SPECIFIED
标称均一增益带宽：	1100 kHz
最小电压增益：	25000
Base Number Matches：	1

电子百科

产品导航

产品型号LM158AH的概述

产品型号LM158AH的Datasheet PDF文件预览

LM158AH相关产品

LM158AH相关文章

IC37:专业IC行业平台