MC100E452应用文章市场行情现货热卖使用介绍供应商报价-中国IC网-芯三七

当前位置：IC37首页_>M字母起始型号索引_>M字母起始型号索引第614页更新时间：2025-01-18 15:10:02

产品型号MC100E452的Datasheet PDF文件预览

SEMICONDUCTOR TECHNICAL DATA

The MC10E/100E452 is a 5-bit differential register with differential data

(inputs and outputs) and clock. The registers are triggered by a positive

transition of the positive clock (CLK) input. A high on the Master Reset

(MR) asynchronously resets all registers so that the Q outputs go LOW.

The differential input structures are clamped so that the inputs of

unused registers can be left open without upsetting the bias network of

the device. The clamping action will assert the D and the CLK sides of the

inputs. Because of the edge triggered flip-flop nature of the device

simultaneously opening both the clock and data inputs will result in an

output which reaches an unidentified but valid state. Note that the input

5-BIT DIFFERENTIAL

clamps only operate when both inputs fall to 2.5V below V

The fully differential design of the device makes it ideal for very high

frequency applications where a registered data path is necessary.

• Differential D, CLK and Q; V

Reference Available

• 1100MHz Min. Toggle Frequency

• Asynchronous Master Reset

• Extended 100E V

Range of – 4.2V to – 5.46V

Pinout: 28-Lead PLCC (Top View)

FN SUFFIX

PLASTIC PACKAGE

CASE 776-02

CCO

CLK

LOGIC DIAGRAM

CCO

* All V

and V

CCO

pins are tied together on the die.

PIN NAMES

Function

D[0:4], D[0:4]

CLK, CLK

VBB

Differential Data Inputs

Master Reset Input

Differential Clock Input

VBB Reference Output

Differential Data Outputs

CLK

Q[0:4], Q[0:4]

12/93

Motorola, Inc. 1996

REV 2

2–1

MC10E452 MC100E452

DC CHARACTERISTICS (V

= V (min) to V (max); V

EE EE

= V

= GND)

CCO

–40°C

0°C

25°C

85°C

Symbol

Characteristic

Min

Typ

Max

Min

Typ

Max

Min

Typ

Max

Min

Typ

Max

Unit Cond

Output Reference

Voltage

10E –1.43

–1.30 –1.38

–1.26 –1.38

–1.27 –1.35

–1.26 –1.38

–1.25 –1.31

–1.26 –1.38

–1.19

–1.26

100E –1.38

Input HIGH

Current

150

µA

Power Supply

Current

10E

100E

102

CMR

Common Mode

Range

–2.0

–0.4

–2.0

–0.4

–2.0

–0.4

–2.0

–0.4

1. V

is referenced to the most positive side of the differential input signal. Normal specified operation is obtained when the input signals are

range and the input swing is greater than V

CMR

within the V

CMR

AC CHARACTERISTICS (V

= V (min) to V (max); V

EE EE

= V = GND)

CCO

–40°C

Typ

0°C to 85°C

Typ

Symbol

Characteristic

Maximum Toggle Frequency

Propagation Delay to Output

Min

Max

Min

Max

Unit

MHz

Condition

1000

1400

1100

1400

MAX

CLK (Diff)

CLK (SE)

425

375

600

625

850

900

475

425

600

625

800

850

PLH

PHL

Setup Time

175

225

750

–50

150

200

700

–50

Hold Time

Reset Recovery Time

Minimum Pulse Width

450

CLK

400

Within-Device Skew

Minimum Input Swing

Rise/Fall Times

skew

150

250

150

275

t /t

475

725

475

675

20–80%

r f

1. Within-device skew is defined as identical transitions on similar paths through a device.

2. Minimum input swing for which AC parameters are guaranteed.

MOTOROLA

2–2

ECLinPS and ECLinPS Lite

DL140 — Rev 4

MC10E452 MC100E452

OUTLINE DIMENSIONS

FN SUFFIX

PLASTIC PLCC PACKAGE

CASE 776–02

ISSUE D

0.007 (0.180)

L –M

Y BRK

-N-

0.007 (0.180)

L –M

-L-

-M-

0.010 (0.250)

0.007 (0.180)

L –M

VIEW D-D

0.007 (0.180)

L –M

0.004 (0.100)

SEATING

PLANE

-T-

VIEW S

0.007 (0.180)

L –M

VIEW S

0.010 (0.250)

L –M

NOTES:

1. DATUMS -L-, -M-, AND -N- DETERMINED

WHERE TOP OF LEAD SHOULDER EXITS

PLASTIC BODY AT MOLD PARTING LINE.

2. DIM G1, TRUE POSITION TO BE MEASURED

AT DATUM -T-, SEATING PLANE.

INCHES

MAX

MILLIMETERS

3. DIM R AND U DO NOT INCLUDE MOLD FLASH.

ALLOWABLE MOLD FLASH IS 0.010 (0.250)

PER SIDE.

4. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

DIM

MIN

12.32

4.20

MAX

12.57

4.57

0.485

0.495

0.180

0.110

0.019

0.485

0.165

0.090

0.013

2.29

2.79

5. CONTROLLING DIMENSION: INCH.

6. THE PACKAGE TOP MAY BE SMALLER THAN

THE PACKAGE BOTTOM BY UP TO 0.012

(0.300). DIMENSIONS R AND U ARE

DETERMINED AT THE OUTERMOST

EXTREMES OF THE PLASTIC BODY

EXCLUSIVE OF MOLD FLASH, TIE BAR

BURRS, GATE BURRS AND INTERLEAD

FLASH, BUT INCLUDING ANY MISMATCH

BETWEEN THE TOP AND BOTTOM OF THE

PLASTIC BODY.

7. DIMENSION H DOES NOT INCLUDE DAMBAR

PROTRUSION OR INTRUSION. THE DAMBAR

PROTRUSION(S) SHALL NOT CAUSE THE H

DIMENSION TO BE GREATER THAN 0.037

(0.940). THE DAMBAR INTRUSION(S) SHALL

NOT CAUSE THE H DIMENSION TO BE

SMALLER THAN 0.025 (0.635).

0.33

0.48

0.050 BSC

1.27 BSC

0.026

0.032

—

0.456

0.048

0.056

0.020

0.66

0.51

0.64

11.43

1.07

—

0.81

—

11.58

1.21

1.42

0.50

0.020

0.025

0.450

0.042

—

10°

2°

10°

0.410

0.040

0.430

—

10.42

1.02

10.92

—

ECLinPS and ECLinPS Lite

DL140 — Rev 4

2–3

MOTOROLA

MC10E452 MC100E452

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding

the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and

specificallydisclaims any and all liability, includingwithoutlimitationconsequentialorincidentaldamages. “Typical” parameters which may be provided in Motorola

datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”

must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of

others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other

applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury

ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola

and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees

arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that

Motorola was negligent regarding the design or manufacture of the part. Motorola and

Opportunity/Affirmative Action Employer.

are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal

How to reach us:

USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;

JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,

P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454

3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315

MFAX: RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609

INTERNET: http://Design–NET.com

ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,

51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298

MC10E452/D

ECLinPS and ECLinPS Lite

DL140 — Rev 4

◊

MOTOROLA

2–4

MC100E452相关文章

配单直通车

北京元坤伟业科技有限公司服务专线: 010-62104931621064316210489162104791 在线联系:

QQ：857273081 复制

QQ：1594462451 复制

柒号芯城电子商务（深圳）有限公司服务专线: 18922803401 在线联系:

QQ：2881677436 复制

QQ：2881620402 复制

深圳市中利达电子科技有限公司服务专线: 0755-13686833545 在线联系:

QQ：1902134819 复制

QQ：2881689472 复制

深圳市芯福林电子有限公司服务专线: 13418564337 在线联系:

QQ：2881495808 复制

QQ：308365177 复制

首天国际（深圳）科技有限公司服务专线: 0755-82807802/82807803 在线联系:

QQ：528164397 复制

QQ：1318502189 复制

MC100E452FN产品参数

型号:	MC100E452FN
是否Rohs认证：	不符合
生命周期：	Obsolete
零件包装代码：	QLCC
包装说明：	PLASTIC, LCC-28
针数：	28
Reach Compliance Code：	not_compliant
HTS代码：	8542.39.00.01
风险等级：	8.06
其他特性：	NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V
计数方向：	RIGHT
系列：	100E
JESD-30 代码：	S-PQCC-J28
JESD-609代码：	e0
长度：	11.505 mm
逻辑集成电路类型：	D FLIP-FLOP
最大频率@ Nom-Sup：	1100000000 Hz
湿度敏感等级：	1
位数：	5
功能数量：	1
端子数量：	28
最高工作温度：	85 °C
最低工作温度：
输出特性：	OPEN-EMITTER
输出极性：	COMPLEMENTARY
封装主体材料：	PLASTIC/EPOXY
封装代码：	QCCJ
封装等效代码：	LDCC28,.5SQ
封装形状：	SQUARE
封装形式：	CHIP CARRIER
峰值回流温度（摄氏度）：	240
电源：	-4.5 V
传播延迟（tpd）：	0.85 ns
认证状态：	Not Qualified
座面最大高度：	4.57 mm
子类别：	Shift Registers
最大供电电压 (Vsup)：	5.7 V
最小供电电压 (Vsup)：	4.2 V
标称供电电压 (Vsup)：	5 V
表面贴装：	YES
技术：	ECL
温度等级：	OTHER
端子面层：	Tin/Lead (Sn80Pb20)
端子形式：	J BEND
端子节距：	1.27 mm
端子位置：	QUAD
处于峰值回流温度下的最长时间：	30
触发器类型：	POSITIVE EDGE
宽度：	11.505 mm
最小 fmax：	1100 MHz
Base Number Matches：	1

电子百科

产品导航

产品型号MC100E452的Datasheet PDF文件预览

MC100E452相关产品..

MC100E452相关文章

IC37:专业IC行业平台