MCR10
Resistors
Table 1
Jumper type
Resistance range
Resistance temperature coefficient
Resistance
Max. 50mΩ
2A
Resistance tolerance
(Ω)
(ppm/°C)
400 200
250
Rated current
F ( 1%)
0.1 ≤ R < 0.15 (E24)
0.15 ≤ R < 10 (E24)
Operating temperature
−55°C to +155°C
10 ≤ R ≤ 2.2M
100
400 200
250
(E24,96)
J
( 5%)
0.1 ≤ R < 0.15 (E24)
0.15 ≤ R < 1 (E24)
1.0 ≤ R < 2.2
2.2 ≤ R < 10
500 350
500
(E24)
(E24)
200
10 ≤ R ≤ 10M (E24)
!Before using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
!
Characteristics
Guaranteed value
Resistor type Jumper type
J : 5% Max. 50mΩ
Item
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
Resistance
F : 1%
Variation of resistance
with temperature
JIS C 5201-1 4.8
Measurement : −55 / +25 / +125°C
See Table.1
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Maximum overload voltage : 200V
Overload
(2.0%+0.1Ω)
Max. 50mΩ
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235 5°C
Duration of immersion : 2.0 0.5s.
Solderability
(1.0%+0.05Ω)
No remarkable abnormality on the appearance.
Max. 50mΩ
JIS C 5201-1 4.18
Soldering condition : 260 5°C
Duration of immersion : 10 1s.
Resistance to
soldering heat
(1.0%+0.05Ω)
(3.0%+0.1Ω)
Max. 50mΩ
JIS C 5201-1 4.19
Test temp. : −55°C~+125°C 5cyc
Rapid change of
temperature
Max. 100mΩ
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h~1,048h
Damp heat, steady state
(3.0%+0.1Ω)
Max. 100mΩ
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h~1,048h
Endurance at 70°C
(3.0%+0.1Ω)
(1.0%+0.05Ω)
(1.0%+0.05Ω)
Max. 100mΩ
Max. 50mΩ
Max. 50mΩ
JIS C 5201-1 4.25.3
155°C
Endurance
Test time : 1,000h~1,048h
JIS C 5201-1 4.29
23 5°C, Immersion cleaning, 5 0.5min.
Solvent : 2-propanol
Resistance to solvent
JIS C 5201-1 4.33
Bend strength of
the end face plating
Without mechanical damage such as breaks.
2/5