MOC3041M各脚功能电路原理芯片引脚定义引脚图及功能IC贸易商-中国IC网-芯三七

当前位置：IC37首页_>M字母起始型号索引_>M字母起始型号索引第966页更新时间：2024-10-24 09:00:02

产品型号MOC3041M的概述

MOC3041M 芯片概述 MOC3041M 是一种广泛应用于光电耦合器的芯片，其主要功能在于实现信号的电气隔离。该芯片属于光耦合器的家族，专门针对高压隔离控制器的设计，能够在高电压应用中安全地传递脉冲信号。这种芯片通常用于开关电源、工业自动化、电机控制和其他需要信号隔离和保护的电子系统中。MOC3041M 利用光电效应，利用光源（如发光二极管）和光电元件（如光电晶体管）来实现电信号的传递。 MOC3041M 的详细参数 MOC3041M 具有以下主要技术参数： - 工作电压 (V_R): 最高可达到 400V。 - 输入正向电流 (I_F): 最大 50 mA。 - 输出电流 (I_C): 最大 100 mA。 - 输入-输出隔离电压 (V_iso): 最小 5000 VRMS。 - 工作温度范围 (T_A): -40°C 至 100°C。 - 封装类型: DIP-8。 - 开关速度...

产品型号MOC3041M的Datasheet PDF文件预览

June 2005

MOC3031M, MOC3032M, MOC3033M, MOC3041M,

MOC3042M, MOC3043M

6-Pin DIP Zero-Cross Optoisolators Triac Driver Output

(250/400 Volt Peak)

Features

Description

■ Simpliﬁes logic control of 115 VAC power

The MOC303XM and MOC304XM devices consist of a AlGaAs

infrared emitting diode optically coupled to a monolithic silicon

detector performing the function of a zero voltage crossing bilat-

eral triac driver.

■ Zero voltage crossing

■ dv/dt of 2000 V/µs typical, 1000 V/µs guaranteed

■ VDE recognized (File # 94766), ordering option V

They are designed for use with a triac in the interface of logic

systems to equipment powered from 115 VAC lines, such as

teletypewriters, CRTs, solid-state relays, industrial controls,

printers, motors, solenoids and consumer appliances, etc.

(e.g., MOC3043VM)

Applications

■ Solenoid/valve controls

■ Static power switches

■ Temperature controls

■ AC motor starters

■

Lighting controls

AC motor drives

E.M. contactors

Solid state relays

Schematic

ANODE

MAIN TERM.

CATHODE

N/C

NC*

ZERO

MAIN TERM.

CROSSING

CIRCUIT

*DO NOT CONNECT

(TRIAC SUBSTRATE)

www.fairchildsemi.com

MOC3031M, MOC3032M, MOC3033M, MOC3041M, MOC3042M, MOC3043M Rev. 1.0.1

Absolute Maximum Ratings (T = 25°C unless otherwise noted)

Parameters

Symbol

Device

Value

Units

TOTAL DEVICE

Storage Temperature

All

-40 to +150

-40 to +85

260 for 10 sec

-40 to +100

7500

°C

STG

Operating Temperature

OPR

Lead Solder Temperature

°C

SOL

Junction Temperature Range

°C

(1)

Isolation Surge Voltage

Vac(pk)

ISO

(peak AC voltage, 60Hz, 1 sec duration)

Total Device Power Dissipation @ 25°C

Derate above 25°C

All

250

2.94

mW/°C

EMITTER

Continuous Forward Current

Reverse Voltage

All

Total Power Dissipation 25°C Ambient

Derate above 25°C

120

1.41

mW/°C

DETECTOR

Off-State Output Terminal Voltage

MOC3031M/2M/3M

250

400

DRM

MOC3041M/2M/3M

Peak Repetitive Surge Current (PW = 100 µs, 120 pps)

Total Power Dissipation @ 25°C Ambient

Derate above 25°C

All

TSM

150

1.76

mW/°C

Note

1. Isolation surge voltage, V_ISO, is an internal device dielectric breakdown rating. For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are

common.

Electrical Characteristics (T = 25°C Unless otherwise speciﬁed)

Individual Component Characteristics

Parameters

Test Conditions

Symbol Device Min Typ Max Units

EMITTER

Input Forward Voltage

I = 30 mA

All

1.25

0.01

1.5

Reverse Leakage Current

= 6 V

100

µA

DETECTOR

Peak Blocking Current, Either Direction

Peak On-State Voltage, Either Direction

Critical Rate of Rise of Off-State Voltage

Rated V

, I = 0 (note 1)

DRM1

All

100

DRM

= 100 mA peak, I = 0

1.8

= 0 (Figure 9, note 3)

dv/dt

1000

V/µs

Transfer Characteristics (T = 25°C Unless otherwise speciﬁed.)

DC Characteristics

Test Conditions

Symbol

Device

Min Typ Max Units

LED Trigger Current

Main terminal voltage = 3V

(note 2)

MOC3031M/

MOC3041M

µA

MOC3032M/

MOC3042M

MOC3033M/

MOC3043M

Holding Current, Either Direction

All

400

www.fairchildsemi.com

MOC3031M, MOC3032M, MOC3033M, MOC3041M, MOC3042M, MOC3043M Rev. 1.0.1

Zero Crossing Characteristics (T = 25°C Unless otherwise speciﬁed.)

Characteristics

Test Conditions

Symbol Device Min Typ Max Units

Inhibit Voltage

I = rated I , MT1-MT2 voltage

All

above which device will not trigger

off-state

Leakage in Inhibited State I = rated I , rated V

, off-state

DRM2

All

500

µA

DRM

Note

1. Test voltage must be applied within dv/dt rating.

2. All devices are guaranteed to trigger at an I_Fvalue less than or equal to max I_FT. Therefore, recommended operating I_Flies between max I_FT

(15 mA for MOC3031M & MOC3041M, 10 mA for MOC3032M & MOC3042M, 5 mA for MOC3033M & MOC3043M) and absolute max I_F(60 mA).

3. This is static dv/dt. See Figure 9 for test circuit. Commutating dv/dt is a function of the load-driving thyristor(s) only.

www.fairchildsemi.com

MOC3031M, MOC3032M, MOC3033M, MOC3041M, MOC3042M, MOC3043M Rev. 1.0.1

Figure 1. LED Forward Voltage vs. Forward Current

Figure 2. On-State Characteristics

800

600

400

200

1.6

1.5

1.4

1.3

1.2

1.1

1.0

0.9

0.8

= 30mA

= 25°C

T_A= -40°C

T_A= 25°C

T_A= 85°C

-200

-400

-600

-800

-4

-3

0.1

100

- LED FORWARD CURRENT (mA)

, ON-STATE VOLTAGE (VOLTS)

Figure 3. Trigger Current vs. Temperature

Figure 4. Leakage Current, I_DRMvs. Temperature

1.3

1.2

1.1

1.0

0.9

0.8

10000

1000

100

NORMALIZED TO

_A= 25^oC

0.1

-40

-20

100

-40

-20

100

T , AMBIENT TEMPERATURE ( ^oC)

T , AMBIENT TEMPERATURE (°C)

www.fairchildsemi.com

MOC3031M, MOC3032M, MOC3033M, MOC3041M, MOC3042M, MOC3043M Rev. 1.0.1

Figure 6. LED Current Required to Trigger vs. LED Pulse Width

Figure 5. I_DRM2- Leakage in Inhibit State vs. Temperature

1.8

NORMALIZED TO

PW >> 100 µs

1.6

1.4

1.2

1.0

0.8

0.6

0.4

= RATED I

-40

-20

100

T , AMBIENT TEMPERATURE (°C)

100

PW , LED TRIGGER PULSE WIDTH (µS)

Figure 7. Holding Current, I_Hvs. Temperature

Figure 8. Inhibit Voltage vs. Temperature

3.2

2.8

2.4

2.0

1.6

1.2

0.8

0.4

0.0

1.3

1.2

1.1

1.0

0.9

0.8

0.7

NORMALIZED TO

= 25° C

-40

-20

100

-40

-20

100

T , AMBIENT TEMPERATURE (°C)

www.fairchildsemi.com

MOC3031M, MOC3032M, MOC3033M, MOC3041M, MOC3042M, MOC3043M Rev. 1.0.1

1. The mercury wetted relay provides a high speed repeated pulse

to the D.U.T.

+250 for MOC303XM

+400 for MOC304XM

Vdc

R_TEST

R = 10 kΩ

2. 100x scope probes are used, to allow high speeds and voltages.

C_TEST

3. The worst-case condition for static dv/dt is established by trigger-

ing the D.U.T. with a normal LED input current, then removing the

PULSE

INPUT

MERCURY

X100

SCOPE

PROBE

WETTED

RELAY

current. The variable R

allows the dv/dt to be gradually

TEST

D.U.T.

increased until the D.U.T. continues to trigger in response to the

applied voltage pulse, even after the LED current has been

removed. The dv/dt is then decreased until the D.U.T. stops trig-

gering. τ_RCis measured at this point and recorded.

Figure 9. Static dv/dt Test Circuit

= 400 V

max

= 250 V

max

APPLIED VOLTAGE

WAVEFORM

APPLIED VOLTAGE

WAVEFORM

252 V

158 V

0.63 V

τ_RC

252

τ_RC

max

0.63 V

τ_RC

158

max

dv/dt =

0 VOLTS

τ_RC

Figure 11. Static dv/dt Test Waveform

(MOC3041M, MOC3042M, MOC3043M)

Figure 10. Static dv/dt Test Waveform

(MOC3031M, MOC3032M, MOC3033M)

Typical circuit (Fig 12, 13) for use when hot line switching is required. In this circuit the “hot” side of the line is switched and the load

connected to the cold or neutral side. The load may be connected to either the neutral or hot line.

is calculated so that I is equal to the rated I of the part, 5 mA for the MOC3033M and MOC3043M, 10 mA for the MOC3032M

F FT

and MOC3042M, or 15 mA for the MOC3031M and MOC3041M. The 39 ohm resistor and 0.01 µF capacitor are for snubbing of the

triac and may or may not be necessary depending upon the particular triac and load used.

R_in

360Ω

180Ω

HOT

V_CC

HOT

V_CC

MOC3041M

MOC3042M

MOC3043M

MOC3031M

MOC3032M

MOC3033M

39Ω

240 VAC

115 VAC

0.01

330

1 k

LOAD

NEUTRAL

LOAD

NEUTRAL

For highly inductive loads (power factor < 0.5), change this value to 360 ohms.

Figure 13. Hot-Line Switching Application Circuit

(MOC3041M, MOC3042M, MOC3043M)

Figure 12. Hot-Line Switching Application Circuit

(MOC3031M, MOC3032M, MOC3033M)

www.fairchildsemi.com

MOC3031M, MOC3032M, MOC3033M, MOC3041M, MOC3042M, MOC3043M Rev. 1.0.1

115 VAC

V_CC

R_in

MOC3031M

MOC3032M

MOC3033M

SCR

180

LOAD

Figure 14. Inverse-Parallel SCR Driver Circuit

(MOC3031M, MOC3032M, MOC3033M)

Suggested method of ﬁring two, back-to-back SCR’s with a Fairchild triac driver. Diodes can be 1N4001; resistors, R1 and R2, are

optional 1 k ohm.

240 VAC

V_CC

R_in

MOC3041M

MOC3042M

MOC3043M

SCR

360

LOAD

Figure 15. Inverse-Parallel SCR Driver Circuit

(MOC3041M, MOC3042M, MOC3043M)

Suggested method of ﬁring two, back-to-back SCR’s with a Fairchild triac driver. Diodes can be 1N4001; resistors, R1 and R2, are

optional 330 ohm.

Note: This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only.

www.fairchildsemi.com

MOC3031M, MOC3032M, MOC3033M, MOC3041M, MOC3042M, MOC3043M Rev. 1.0.1

Package Dimensions (Through Hole)

Package Dimensions (Surface Mount)

0.350 (8.89)

0.320 (8.13)

0.350 (8.89)

0.320 (8.13)

Pin 1 ID

0.390 (9.90)

0.332 (8.43)

0.260 (6.60)

0.240 (6.10)

0.260 (6.60)

0.240 (6.10)

0.070 (1.77)

0.040 (1.02)

0.070 (1.77)

0.040 (1.02)

0.320 (8.13)

0.014 (0.36)

0.010 (0.25)

0.014 (0.36)

0.010 (0.25)

0.200 (5.08)

0.115 (2.93)

0.200 (5.08)

0.115 (2.93)

0.012 (0.30)

0.008 (0.20)

0.100 (2.54)

0.015 (0.38)

0.025 (0.63)

0.020 (0.51)

0.100 [2.54]

0.020 (0.50)

0.016 (0.41)

15°

0.035 (0.88)

0.012 (0.30)

0.020 (0.50)

0.016 (0.41)

0.100 (2.54)

0.012 (0.30)

Package Dimensions (0.4” Lead Spacing)

Recommended Pad Layout for

Surface Mount Leadform

0.350 (8.89)

0.320 (8.13)

PIN 1 ID

0.070 (1.78)

0.260 (6.60)

0.240 (6.10)

0.060 (1.52)

0.070 (1.77)

0.040 (1.02)

0.014 (0.36)

0.425 (10.79)

0.100 (2.54)

0.305 (7.75)

0.010 (0.25)

0.030 (0.76)

0.200 (5.08)

0.115 (2.93)

0.100 (2.54)

0.015 (0.38)

0.012 (0.30)

0.100 [2.54]

0.020 (0.50)

0.016 (0.41)

0.008 (0.21)

0.425 (10.80)

0.400 (10.16)

NOTE

All dimensions are in inches (millimeters)

www.fairchildsemi.com

MOC3031M, MOC3032M, MOC3033M, MOC3041M, MOC3042M, MOC3043M Rev. 1.0.1

Ordering Information

Option

Order Entry Identiﬁer

Description

SR2

Surface Mount Lead Bend

Surface Mount; Tape and reel

0.4" Lead Spacing

VDE 0884

VDE 0884, 0.4" Lead Spacing

VDE 0884, Surface Mount

VDE 0884, Surface Mount, Tape & Reel

SR2V

Carrier Tape Specifications (White Package, -M Suffix)

12.0 0.1

4.5 0.20

2.0 0.05

Ø1.5 MIN

1.75 0.10

0.30 0.05

4.0 0.1

11.5 1.0

24.0 0.3

9.1 0.20

21.0 0.1

Ø1.5 0.1/-0

10.1 0.20

0.1 MAX

User Direction of Feed

NOTE

All dimensions are in inches (millimeters)

www.fairchildsemi.com

MOC3031M, MOC3032M, MOC3033M, MOC3041M, MOC3042M, MOC3043M Rev. 1.0.1

Marking Information

MOC3031V

XX YY Q

Deﬁnitions

Fairchild logo

Device number

VDE mark (Note: Only appears on parts ordered with VDE

option – See order entry table)

One digit year code, e.g., ‘3’

Two digit work week ranging from ‘01’ to ‘53’

Assembly package code

*Note – Parts that do not have the ‘V’ option (see deﬁnition 3 above) that are marked with

date code ‘325’ or earlier are marked in portrait format.

Reﬂow Proﬁle (White Package, -M Sufﬁx)

300

280

260

240

220

200

180

160

140

120

100

260°C

>245°C = 42 Sec

Time above

183°C = 90 Sec

°C

1.822°C/Sec Ramp up rate

33 Sec

120

180

270

360

Time (s)

www.fairchildsemi.com

MOC3031M, MOC3032M, MOC3033M, MOC3041M, MOC3042M, MOC3043M Rev. 1.0.1

TRADEMARKS

The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is

not intended to be an exhaustive list of all such trademarks.

ACEx™

PowerSaver™

SuperSOT™-8

SyncFET™

TinyLogic

ISOPLANAR™

LittleFET™

MICROCOUPLER™

MicroFET™

MicroPak™

MICROWIRE™

MSX™

FAST

ActiveArray™

Bottomless™

Build it Now™

CoolFET™

CROSSVOLT™

DOME™

EcoSPARK™

E²CMOS™

EnSigna™

FACT™

PowerTrench

FASTr™

FPS™

FRFET™

GlobalOptoisolator™

GTO™

QFET

QS™

TINYOPTO™

TruTranslation™

UHC™

QT Optoelectronics™

Quiet Series™

RapidConfigure™

RapidConnect™

μSerDes™

SILENT SWITCHER

SMART START™

SPM™

UltraFET

HiSeC™

I²C™

UniFET™

VCX™

Wire™

MSXPro™

OCX™

i-Lo™

ImpliedDisconnect™

IntelliMAX™

OCXPro™

OPTOLOGIC

OPTOPLANAR™

PACMAN™

POP™

Power247™

PowerEdge™

FACT Quiet Series™

Stealth™

Across the board. Around the world.™

SuperFET™

SuperSOT™-3

SuperSOT™-6

The Power Franchise

Programmable Active Droop™

DISCLAIMER

FAIRCHILD SEMICONDUCTOR RESERVESTHE RIGHTTO MAKE CHANGES WITHOUTFURTHER NOTICETOANY

PRODUCTS HEREINTO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOTASSUMEANYLIABILITY

ARISING OUTOFTHEAPPLICATION OR USE OFANYPRODUCTOR CIRCUITDESCRIBED HEREIN; NEITHER DOES IT

CONVEYANYLICENSE UNDER ITS PATENTRIGHTS, NORTHE RIGHTS OF OTHERS.

LIFE SUPPORT POLICY

FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT

DEVICES OR SYSTEMS WITHOUTTHE EXPRESS WRITTENAPPROVALOF FAIRCHILD SEMICONDUCTOR CORPORATION.

As used herein:

1. Life support devices or systems are devices or

systems which, (a) are intended for surgical implant into

the body, or (b) support or sustain life, or (c) whose

failure to perform when properly used in accordance

with instructions for use provided in the labeling, can be

reasonably expected to result in significant injury to the

user.

2. A critical component is any component of a life

support device or system whose failure to perform can

be reasonably expected to cause the failure of the life

support device or system, or to affect its safety or

effectiveness.

PRODUCT STATUS DEFINITIONS

Definition of Terms

Datasheet Identification

Product Status

Definition

Advance Information

Formative or

In Design

This datasheet contains the design specifications for

product development. Specifications may change in

any manner without notice.

Preliminary

First Production

This datasheet contains preliminary data, and

supplementary data will be published at a later date.

Fairchild Semiconductor reserves the right to make

changes at any time without notice in order to improve

design.

No Identification Needed

Obsolete

Full Production

This datasheet contains final specifications. Fairchild

Semiconductor reserves the right to make changes at

any time without notice in order to improve design.

Not In Production

This datasheet contains specifications on a product

that has been discontinued by Fairchild semiconductor.

The datasheet is printed for reference information only.

Rev. I16

MOC3041M相关文章

配单直通车

柒号芯城电子商务（深圳）有限公司服务专线: 0755-83209937 在线联系:

QQ：2881677436 复制

QQ：2881620402 复制

深圳市中利达电子科技有限公司服务专线: 0755-83200645/13686833545 在线联系:

QQ：1902134819 复制

QQ：2881689472 复制

首天国际（深圳）科技有限公司服务专线: 0755-82807802/82807803 在线联系:

QQ：528164397 复制

QQ：1318502189 复制

深圳市芯福林电子有限公司服务专线: 13418564337 在线联系:

QQ：2881495808 复制

QQ：308365177 复制

北京元坤伟业科技有限公司服务专线: 010-62104931621064316210489162104791 在线联系:

QQ：857273081 复制

QQ：1594462451 复制

MOC3041M产品参数

型号:	MOC3041M
是否无铅：	不含铅
是否Rohs认证：	符合
生命周期：	Active
包装说明：	DIP-6
Reach Compliance Code：	unknown
风险等级：	5.67
Is Samacsys：	N
配置：	SINGLE
最大正向电流：	0.06 A
标称输入触发电流：	15 mA
最大绝缘电压：	7500 V
JESD-609代码：	e3
元件数量：	1
最高工作温度：	85 °C
最低工作温度：	-40 °C
光电设备类型：	TRIAC OUTPUT OPTOCOUPLER WITH ZERO CRSVR
最小断态峰值电压：	400 V
端子面层：	MATTE TIN
Base Number Matches：	1

电子百科

产品导航

产品型号MOC3041M的概述

产品型号MOC3041M的Datasheet PDF文件预览

MOC3041M相关产品

MOC3041M相关文章

IC37:专业IC行业平台