Varistor Products
High Energy Industrial
DA/DB Varistor Series
Absolute Maximum Ratings For ratings of individual members of a series, see Device Ratings and Specifications chart
Continuous:
DA/DB SERIES
UNITS
Steady State Applied Voltage:
AC Voltage Range (V
DC Voltage Range (V
Transient:
Peak Pulse Current (I
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 to 750
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 to 970
V
V
M(AC)RMS
M(DC)
2
)
TM
For 8/20µs Current Wave (See Figure 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40,000
Single Pulse Energy Range
A
For 2ms Current Square Wave (W ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270 to 1050
Operating Ambient Temperature Range (T ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55 to 85
A
J
oC
TM
Storage Temperature Range (T
STG
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55 to 125
oC
Temperature Coefficient (αV) of Clamping Voltage (V ) at Specified Test Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <0.01
%/oC
V
C
Hi-Pot Encapsulation (Isolation Voltage Capability) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5000
(Dielectric must withstand indicated DC voltage for one minute per MIL-STD 202, Method 301)
Insulation Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000
MΩ
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device
at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Device Ratings and Specifications
o
o
MAXIMUM RATINGS (85 C)
SPECIFICATIONS (25 C)
CONTINUOUS TRANSIENT
MAX CLAMP-
ING VOLT V
AT 200A
CURRENT
(8/20µs)
C
PEAK
CURRENT
(8/20µs)
VARISTOR VOLTAGE AT
1mA DC TEST
TYPICAL
CAPACI-
TANCE
ENERGY
(2ms)
V
V
CURRENT
RMS
DC
PART NUMBER AND
DEVICE BRANDING
V
V
W
I
MIN
(V)
V
MAX
(V)
V
C
f = 1MHz
(pF)
M(AC)
M(DC)
TM
TM
N(DC)
DA
DB
(V)
(V)
(J)
(A)
(V)
(V)
V131DA40
V151DA40
V251DA40
V271DA40
V321DA40
V421DA40
V481DA40
V511DA40
V571DA40
V661DA40
V751DA40
V131DB40
V151DB40
V251DB40
V271DB40
V321DB40
V421DB40
V481DB40
V511DB40
V571DB40
V661DB40
V751DB40
130
150
250
275
320
420
480
510
575
660
750
175
200
330
369
420
560
640
675
730
850
970
270
300
370
400
460
600
650
700
770
900
1050
400001
400002
40000
40000
40000
40000
40000
40000
40000
40000
40000
184
212
354
389
462
610
670
735
805
940
1080
200
240
390
430
510
680
750
820
910
228
268
429
473
561
748
825
910
1000
1160
1320
345
10000
8000
5000
4500
3800
3000
2700
2500
2200
2000
1800
405
650
730
830
1130
1240
1350
1480
1720
2000
1050
1200
NOTE: Average power dissipation of transients not to exceed 2.0W.
1: Peak current applies to applications rated up to 115VRMS. Peak Current is 30kA for applications greater than 115V
.
.
2: Peak current applies to applications rated up to 132VRMS. Peak Current is 30kA for applications greater than 132VRMS
RMS
87
www. lit t elf us e. c om