ADM1485
ABSOLUTE MAXIMUM RATINGS*
(T
A
= 25°C, unless otherwise noted.)
PIN FUNCTION DESCRIPTIONS
V
CC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Inputs
Driver Input (DI) . . . . . . . . . . . . . . . .–0.3 V to V
CC
+ 0.3 V
Control Inputs (DE,
RE)
. . . . . . . . . .–0.3 V to V
CC
+ 0.3 V
Receiver Inputs (A, B) . . . . . . . . . . . . . . . . . . –9 V to +14 V
Outputs
Driver Outputs (A, B) . . . . . . . . . . . . . . . . . . –9 V to +14 V
Receiver Output . . . . . . . . . . . . . . . . .–0.5 V to V
CC
+ 0.5 V
Power Dissipation 8-Lead MSOP . . . . . . . . . . . . . . . 900 mW
θ
JA
, Thermal Impedance . . . . . . . . . . . . . . . . . . . 206°C/W
Power Dissipation 8-Lead PDIP . . . . . . . . . . . . . . . . 500 mW
θ
JA
, Thermal Impedance . . . . . . . . . . . . . . . . . . . 130°C/W
Power Dissipation 8-Lead SOIC . . . . . . . . . . . . . . . . 450 mW
θ
JA
, Thermal Impedance . . . . . . . . . . . . . . . . . . . 170°C/W
Operating Temperature Range
Commercial (J Version) . . . . . . . . . . . . . . . . . . 0°C to 70°C
Industrial (A Version) . . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . . 300°C
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . . 215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220°C
*Stresses
above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum ratings
for extended periods of time may affect device reliability.
Pin Mnemonic Function
No.
1
RO
Receiver Output. When enabled if A > B
by 200 mV, then RO = High. If A < B by
200 mV, then RO = Low.
Receiver Output Enable. A low level
enables the receiver output, RO. A high
level places it in a high impedance state.
Driver Output Enable. A high level enables
the driver differential outputs, A and B. A low
level places it in a high impedance state.
Driver Input. When the driver is enabled,
a logic low on DI forces A low and B high
while a logic high on DI forces A high and
B low.
Ground Connection, 0 V.
Noninverting Receiver Input A/Driver
Output A.
Inverting Receiver Input B/Driver Output B
Power Supply, 5 V
±
5%.
PIN CONFIGURATION
2
RE
3
DE
4
DI
5
6
7
8
GND
A
B
V
CC
RO
1
8
V
CC
Table I. Transmitting
RE
2
7
B
TOP VIEW
DE
3
(Not to Scale)
6
A
ADM1485
Inputs
DE
1
1
0
DI
1
0
X
Outputs
B
0
1
Z
A
1
0
Z
DI
4
5
GND
Table II. Receiving
RE
0
0
0
1
Inputs
A-B
≥
+0.2 V
≤
–0.2 V
Inputs Open
X
Outputs
RO
1
0
1
Z
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
ADM1485 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
REV.
–3–
AD [ ANALOG DEVICES ]
