SPECIFICATIONS
(CONT)
All specifications T
MIN
to T
MAX
, AV
DD
= DV
DD
= +5V, f
XIN
= 10MHz, programmable gain amplifier setting of 1, Turbo Mode Rate of 1, REF
OUT
disabled,V
BIAS
disabled,
and external 2.5V reference, unless otherwise specified.
ADS1210U, P/ADS1211U, P, E
PARAMETER
POWER SUPPLY REQUIREMENTS
Power Supply Voltage
Power Supply Current:
Analog Current
Digital Current
Additional Analog Current with
REF
OUT
Enabled
V
BIAS
Enabled
Power Dissipation
CONDITIONS
MIN
4.75
2
3.5
1.6
1
26
37
17
27
11
–40
–60
TYP
MAX
5.25
UNITS
V
mA
mA
mA
mA
mW
mW
mW
mW
mW
°C
°C
No Load
TMR of 16
f
XIN
= 2.5MHz
= 2.5MHz, TMR of 16
Sleep Mode
40
60
f
XIN
TEMPERATURE RANGE
Specified
Storage
+85
+125
NOTES: (1) In order to achieve the converter’s full-scale range, the input must be fully differential (A
IN
N = 2 • REF
IN
– A
IN
P). If the input is single-ended (A
IN
N or
A
IN
P is fixed), then the full scale range is one-half that of the differential range. (2) This range is set with external resistors and V
BIAS
(as described in the text).
Other ranges are possible. (3) Input impedance is higher with lower f
XIN
. (4) Applies after calibration. (5) After system calibration, these errors will be of the order
of the effective resolution of the converter. Refer to the Typical Performance Curves which apply to the desired mode of operation. (6) Recalibration can remove
these errors. (7) The specification also applies at f
DATA
/i, where i is 2, 3, 4, etc. (8) Voltages at the analog inputs must remain within AGND to AV
DD
. (9) The common-
mode rejection test is performed with a 100mV differential input.
ABSOLUTE MAXIMUM RATINGS
Analog Input: Current ................................................
±100mA,
Momentary
±10mA,
Continuous
Voltage ................................... AGND –0.3V to AV
DD
+0.3V
AV
DD
to DV
DD
........................................................................... –0.3V to 6V
AV
DD
to AGND ......................................................................... –0.3V to 6V
DV
DD
to DGND ......................................................................... –0.3V to 6V
AGND to DGND ................................................................................
±0.3V
REF
IN
Voltage to AGND ............................................ –0.3V to AV
DD
+0.3V
Digital Input Voltage to DGND .................................. –0.3V to DV
DD
+0.3V
Digital Output Voltage to DGND ............................... –0.3V to DV
DD
+0.3V
Lead Temperature (soldering, 10s) .............................................. +300°C
Power Dissipation (Any package) .................................................. 500mW
PACKAGE/ORDERING INFORMATION
PACKAGE
DRAWING
NUMBER
(1)
218
219
243
239
324
TEMPERATURE
RANGE
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
PRODUCT
ADS1210P
ADS1210U
ADS1211P
ADS1211U
ADS1211E
PACKAGE
18-Pin Plastic DIP
18-Lead SOIC
24-Pin Plastic DIP
24-Lead SOIC
28-Lead SSOP
NOTE: (1) For detailed drawing and dimension table, please see end of data
sheet, or Appendix C of Burr-Brown IC Data Book.
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with ap-
propriate precautions. Failure to observe proper handling and
installation procedures can cause damage.
Electrostatic discharge can cause damage ranging from
performance degradation to complete device failure. Burr-
Brown Corporation recommends that all integrated circuits be
handled and stored using appropriate ESD protection
methods.
®
3
ADS1210, 1211
BURR-BROWN [ BURR-BROWN CORPORATION ]
