CAT24WC66
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias ................. –55°C to +125°C
Storage Temperature ....................... –65°C to +150°C
Voltage on Any Pin with
Respect to Ground
(1)
........... –2.0V to +V
CC
+ 2.0V
V
CC
with Respect to Ground ............... –2.0V to +7.0V
Package Power Dissipation
Capability (T
A
= 25°C) ................................... 1.0W
RELIABILITY CHARACTERISTICS
Symbol
NEND
(3)
TDR
(3)
VZAP
(3)
ILTH
(3)(4)
Parameter
Endurance
Data Retention
ESD Susceptibility
Latch-up
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current
(2)
........................ 100mA
*COMMENT
Stresses above those listed under “Absolute Maximum Ratings” may
cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions
outside of those listed in the operational sections of this specification is not
implied. Exposure to any absolute maximum rating for extended periods
may affect device performance and reliability.
Reference Test Method
MIL-STD-883, Test Method 1033
MIL-STD-883, Test Method 1008
MIL-STD-883, Test Method 3015
JEDEC Standard 17
Min
1,000,000
100
2000
100
Max
Units
Cycles/Byte
Years
Volts
mA
D.C. OPERATING CHARACTERISTICS
V
CC
= +1.8V to +6.0V, unless otherwise specified.
Symbol
I
CC
I
SB(5)
I
LI
I
LO
V
IL
V
IH
V
OL1
V
OL2
Parameter
Power Supply Current
Standby Current (VCC = 5V)
Input Leakage Current
Output Leakage Current
Input Low Voltage
Input High Voltage
Output Low Voltage
(V
CC
= +3.0V)
Output Low Voltage
(V
CC
= +1.8V)
I
OL
= 3.0 mA
I
OL
= 1.5 mA
Test Conditions
f
SCL
= 100 kHz
V
IN
= GND or V
CC
V
IN
= GND to V
CC
V
OUT
= GND to V
CC
-1
V
CC
x 0.7
Min
Typ
Max
3
1
10
10
V
CC
x 0.3
V
CC
+ 0.5
0.4
0.5
Units
mA
µA
µA
µA
V
V
V
V
CAPACITANCE
T
A
= 25°C, f = 1.0 MHz, V
CC
= 5V
Symbol
C
I/O(3)
C
IN(3)
Parameter
Input/Output Capacitance
(SDA)
Input Capacitance
(A0, A1, A2, SCL, WP)
Conditions
V
I/O
= 0V
V
IN
= 0V
Min
Typ
Max
8
6
Units
pF
pF
Note:
(1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is V
CC
+0.5V, which may overshoot to V
CC
+ 2.0V for periods of less than 20ns.
(2) Output shorted for no more than one second. No more than one output shorted at a time.
(3) This parameter is tested initially and after a design or process change that affects the parameter.
(4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to V
CC
+1V.
(5) Maximum standby current (I
SB
) = 10µA for the Automotive and Extended Automotive temperature range.
Doc. No. 1037, Rev. H
2
CATALYST [ CATALYST SEMICONDUCTOR ]
