Notes:
loads VOH will approach VCC as IOH
approaches zero amps.
7. Maximum pulse width = 1 ms,
maximum duty cycle = 20%.
under the same test condition.
11. Pins 1 and 4 need to be connected to
LED common.
12. Common mode transient immunity in
the high state is the maximum
tolerable |dVCM/dt| of the common
mode pulse, VCM, to assure that the
output will remain in the high state
(i.e., VO > 15.0 V).
13. Common mode transient immunity in
a low state is the maximum tolerable
|dVCM/dt| of the common mode
pulse, VCM, to assure that the output
will remain in a low state (i.e.,
VO < 1.0 V).
14. This load condition approximates the
gate load of a 1200 V/25 A IGBT.
15. Pulse Width Distortion (PWD) is
defined as |tPHL-tPLH| for any given
device.
1. Derate linearly above 70°C free-air
temperature at a rate of 0.3 mA/°C.
2. Maximum pulse width = 10 µs,
maximum duty cycle = 0.2%. This
value is intended to allow for
component tolerances for designs
with IO peak minimum = 0.5 A. See
Applications section for additional
details on limiting IOH peak.
3. Derate linearly above 70°C free-air
temperature at a rate of 4.8 mW/°C.
4. Derate linearly above 70°C free-air
temperature at a rate of 5.4 mW/°C.
The maximum LED junction tempera-
ture should not exceed 125°C.
5. Maximum pulse width = 50 µs,
maximum duty cycle = 0.5%.
8. In accordance with UL1577, each
optocoupler is proof tested by
applying an insulation test voltage
≥ 3000 Vrms for 1 second (leakage
detection current limit, II-O ≤ 5 µA).
This test is performed before the
100% production test for partial
discharge (method b) shown in the
VDE 0884 Insulation Characteristics
Table, if applicable.
9. Device considered a two-terminal
device: pins 1, 2, 3, and 4 shorted
together and pins 5, 6, 7, and 8
shorted together.
10. The difference between tPHL and tPLH
between any two HCPL-3150 parts
6. In this test VOH is measured with a dc
load current. When driving capacitive
0
-1
0.50
I
I
V
V
= 7 to 16 mA
= -100 mA
I
= 7 to 16 mA
F
OUT
F
V
V
V
= V - 4 V
OUT
CC
100 °C
25 °C
-40 °C
= 15 to 30 V
= 0 V
= 15 to 30 V
= 0 V
CC
EE
CC
EE
-2
-3
-4
0.45
0.40
0.35
-1
-2
I
V
V
= 7 to 16 mA
= 15 to 30 V
-3
-4
F
CC
-5
-6
0.30
0.25
= 0 V
EE
-40 -20
0
20 40 60 80 100
0
0.2
0.4
0.6
0.8
1.0
-40 -20
0
20 40 60 80 100
T
– TEMPERATURE – °C
I
– OUTPUT HIGH CURRENT – A
OH
T
– TEMPERATURE – °C
A
A
Figure 1. VOH vs. Temperature.
Figure 2. IOH vs. Temperature.
Figure 3. VOH vs. IOH
.
1.0
1.0
5
V
= -3.0 to 0.8 V
F(OFF)
= 100 mA
V
V
V
= -3.0 to 0.8 V
= 15 to 30 V
= 0 V
F(OFF)
CC
EE
I
OUT
V
V
= 15 to 30 V
= 0 V
CC
EE
0.8
0.6
0.4
0.8
0.6
0.4
4
3
2
V
V
V
V
= -3.0 to 0.8 V
F(OFF)
= 2.5 V
OUT
0.2
0
0.2
0
1
0
100 °C
25 °C
-40 °C
= 15 to 30 V
= 0 V
CC
EE
-40 -20
0
20 40 60 80 100
-40 -20
0
20 40 60 80 100
T – TEMPERATURE – °C
A
0
0.2
0.4
0.6
0.8
1.0
T
– TEMPERATURE – °C
I
– OUTPUT LOW CURRENT – A
A
OL
Figure 4. VOL vs. Temperature.
Figure 5. IOL vs. Temperature.
Figure 6. VOL vs. IOL.
1-203
HP [ HEWLETT-PACKARD ]
