MAS6180A2TC05 参数 Datasheet PDF下载

DA6180.001

27 December, 2006

6)

ABSOLUTE MAXIMUM RATINGS

All Voltages with Respect to Ground

Parameter

Supply Voltage

Input Voltage

ESD Rating

Symbol

V

DD

-V

SS

V

IN

V

ESD

Conditions

Min

- 0.3

V

SS

-0.3

±2

Max

5.5

V

DD

+0.3

Unit

V

V

kV

Latchup Current Limit

I

LUT

For all pins,

Human Body Model (HBM),

ESD Association Standard

Test Method ESD-STM5.1-

1998, C

ESD

= 100 pF,

Rs = 1500

Ω),

For all pins,

test according to

Micro Analog Systems

specification ESQ0141.

See note below.

±100

mA

Operating Temperature

Storage Temperature

T

OP

T

ST

-40

- 55

+85

+150

°

C

°

C

Stresses beyond those listed may cause permanent damage to the device. The device may not operate under these conditions, but it will

not be destroyed.

Note:

In latchup testing the supply voltages are connected normally to the tested device. Then pulsed test current is fed to each input

separately and device current consumption is observed. If the device current consumption increases suddenly due to test current pulses

and the abnormally high current consumption continues after test current pulses are cut off then the device has gone to latch up. Current

pulse is turned on for 10 ms and off for 20 ms.

ELECTRICAL CHARACTERISTICS

Operating Conditions: VDD = 1.5V, Temperature = 25° unless otherwise specified.

C,

Parameter

Operating Voltage

Current Consumption

Symbol

V

DD

I

DD

Conditions

VDD=1.5 V, Vin=0

µVrms

VDD=1.5 V, Vin=20 mVrms

VDD=3.6 V, Vin=0

µVrms

VDD=3.6 V, Vin=20 mVrms

See note below.

Min

1.10

40

24

Typ

55

40

58

43

Max

3.6

80

65

Unit

V

µA

Stand-By Current

Input Frequency Range

Minimum Input Voltage

Maximum Input Voltage

Receiver Input Resistance

Receiver Input Capacitance

Input Levels |l

IN

|<0.5

µA

Output Current

V

OL

<0.2 V

DD

;V

OH

>0.8 V

DD

Output Pulse

I

DDoff

f

IN

V

IN min

V

IN max

R

RFI

C

RFI

V

IL

V

IH

|I

OUT

|

T

100ms

T

200ms

T

500ms

T

800ms

40

0.4

20

Differential Input,

f=40 kHz..77.5 kHz

V

DD

-0.35

5

1

µVrms ≤

V

IN

≤

20 mVrms

1

µVrms ≤

V

IN

≤

20 mVrms

1

µVrms ≤

V

IN

≤

20 mVrms

1

µVrms ≤

V

IN

≤

20 mVrms

Fast Start-up, Vin=0.4

µVrms

Fast Start-up, Vin=20 mVrms

50

150

400

700

500

800

1.3

3.5

50

600

0.5

0.1

100

1

µA

kHz

µVrms

mVrms

kΩ

pF

V

µA

0.35

140

230

600

900

ms

ms

ms

ms

s

Startup Time

Output Delay Time

T

Start

T

Delay

100

ms

Note:

Stand-by current consumption may increase if V

IH

and V

IL

differ from VDD and 0 respectively.

3 (9)