CMOS
Pin Description
Pin #
1
2-9
Name
V
SS
S0-S7
Ground.
Description
MT9085
Serial Input/Outputs
(TTL compatible with internal pullups). Time division, multiplexed serial
bus streams; inputs in serial to parallel mode (MCA=0), and outputs in parallel to serial mode
(MCA=1). Data rate on the serial streams can be selected to be 2.048 Mbit/s (2/4S=0) or 4.096
Mbit/s (2/4S=1). Refer to Figures 3, 4 and 5 for functional timing information.
Ground.
10
11-16
17
18
V
SS
V
DD
V
SS
S8-S13
Serial Input/Outputs.
See description for pins 2 - 9 above.
Supply Input.
+5V.
Ground.
19-20 S14-S15
Serial Input/Outputs.
See description for pins 2 - 9 above.
21-26 S16-S21
Serial Input/Outputs
(TTL compatible with internal pullups). Time division, multiplexed serial
bus streams which are configured as inputs in serial to parallel mode (MCA =0), and outputs in
parallel to serial mode (MCA=1). Data is clocked at 2.048 Mbit/s (2/4S = 0). These input/
outputs are inactive when the device is configured for 4.096 Mbit/s operation (2/4S=1).
27
V
SS
V
SS
V
DD
CKD
Ground.
28-33 S22-S27
Serial Input/Outputs.
See description for pins 21-26 above.
34
35
Ground.
Supply Input +5V.
36-39 S28-S31
Serial Input/Outputs.
See description for pins 21-26 above.
40
Clock Delay (Input).
Control input which configures internal device timing.
CKD=0 Internal master counter is reset at the system frame boundary established by the
frame pulse (F0i).
CKD=1 Internal master counter is reset one C16 clock period after system frame boundary.
All data input/output will be delayed by one C16 clock period.
Timing for data input/output and for OE is affected by the level asserted on CKD. The relative
phase between the frame boundary established by F0i and output signals F0o, C2o, C4o,
DFPo, DFPo and CFPo is also affected by the state of the CKD input. See descriptions
pertaining to each specific pin for more information.
4.096MHz Clock Input.
The 4.096 MHz clock signal must be phase locked to the 16.384 MHz.
clock. The falling edge of C4i is used to clock in the frame pulse (F0i).
Output Enable (Input).
When low, output data bus (serial or parallel) is actively driven.
When set high, the output bus drivers are disabled. In serial to parallel mode, the outputs are
disabled immediately after OE is taken High. See Figures 6 and 21 for timing information
pertaining to parallel to serial mode.
2.048/4.096 Mbit/s Select (Input).
Selects the data rate for the time division, multiplexed
serial streams. When tied low, the data rate is 2.048 Mbit/s. When tied high, the data rate is
4.096 Mbit/s.
Mode Control-A (Input).
The device will perform a serial to parallel conversion when this
input is tied low. When the input is tied high, the device operates in the parallel to serial mode.
Internal Connection.
Must be tied to V
SS
for normal device operation.
Internal Connection.
Should be left unconnected.
Connect Memory Frame Pulse (Output).
Framing signal with a nominal 8 kHz frequency;
goes low 71 (CKD=0) or 68 (CKD=1) C16 clock cycles before the frame boundary established
by F0i. The signal is used by the connection memory in a typical 1k or 2k switch configuration.
See Figure 15 for timing information.
2-127
41
42
C4i
OE
43
2/4S
44
45
46
47
MCA
IC
IC
CFPo
MITEL [ MITEL NETWORKS CORPORATION ]
