Specifications
■
Characteristics
Electrical Rating (See note 4)
Operating speed
Operating frequency
Insulation resistance
Contact resistance
Dielectric strength (See note 2)
0.1 A at 30 VDC, resistive
0.1 mm/s to 1 m/s (pin plunger models)
Mechanical: 400 operations/minute max.
Electrical: 30 operations/minute max.
100 MΩ min. at 500 VDC
100 mΩ max. including connector and 50-mm AWG28 lead wire resistance
1,000 VAC at 50/60 Hz for 1 minute between terminals of the same polarity
1,500 VAC at 50/60 Hz for 1 minute between charged metal part and ground
1,500 VAC at 50/60 Hz for 1 minute between non-charged metal part and each terminal
Malfunction: 10 to 55 Hz, 1.5-mm double amplitude
Destruction: 1,000 m/s
2
(approx. 100G) max.
Malfunction: 300 m/s
2
(approx. 30G) max.
IEC IP40
175
-25°C to 85°C (at 60% RH max) with no icing
85% max. (for 5°C to 35°C)
Mechanical: 500,000 operations at 60 operations/minute
Electrical: 200,000 operations at 30 operations/minute
Approx. 2 g (pin plunger model)
Vibration resistance (See note 3)
Shock resistance (See note 3)
Degree of protection
Proof tracking index (PTI)
Ambient operating temperature
Ambient operating humidity
Life expectancy
Weight
Degree of protection against electric shock
Class I
Note: 1.
Data shown are of initial value.
2.
The dielectric strength shown is measured using a separator between the switch and metal mounting plate.
3.
For the pin plunger models, the above values apply for use at the free position and total travel position. For the lever models, they apply
at the total travel position. Contact opening or closing time is within 1 ms.
4.
The electrical ratings apply under the following test conditions: Ambient Temperature = 20
±
2
°
C, Ambient Humidity = 65
±
5%, Operating frequency = 30 op-
erations/min.
■
Approved Standards
UL Recognized/CSA Certified
Rated voltage
30 VDC
0.1 A
D3M
■
Contact Specifications
Item
Specification
Material
Contact gap
Inrush current
D3M
Minimum applicable load
(see note)
Crossbar
Gold alloy
0.5 mm
1 A max.
1 mA at 5 VDC
Specification
EN61058-1 (TÜV Rheinland approval)
Rated voltage
30 VDC
0.1 A
Testing conditions: 1E5 (100,000 operations), T85 (0°C to 85°C)
Note:
Minimum applicable loads are indicated by N standard refer-
ence values. This value represents the failure rate at a 60%
(λ
60
) reliability level (JIS C5003).
The equation
λ
60
=0.5 x 10
-6
/ operations indicates that a failure
rate of 1/2,000,000 operations can be expected at a reliability
level of 60%
Engineering Data
■
Mounting Holes
All switches may be panel mounted using M2.3 mounting screws with
plane washers or spring washers to securely mount the switch.
Tighten the screws to a torque of 0.23 to 0.26 N·m.
Two, 2.4-dia. mounting hole or M2.3 screw hole
■
Contact Form
SPST-NC
SPST-NO
9.5
±0.1
58
Subminiature Snap Action Switch
D3M
OMRON [ OMRON ELECTRONICS LLC ]
