欢迎访问ic37.com |
会员登录 免费注册
发布采购

RS7302-285DLNNEP 参数 Datasheet PDF下载

RS7302-285DLNNEP图片预览
型号: RS7302-285DLNNEP
PDF下载: 下载PDF文件 查看货源
内容描述: 600毫安可调及固定电压LDO线性稳压器,带有使能,快速放电和Soft.Start [600mA Adjustable & Fixed Voltage LDO Linear Regulator with Enable, Fast Discharge & Soft.Start]
分类和应用: 稳压器
文件页数/大小: 11 页 / 696 K
品牌: ORISTER [ ORISTER CORPORATION ]
 浏览型号RS7302-285DLNNEP的Datasheet PDF文件第1页浏览型号RS7302-285DLNNEP的Datasheet PDF文件第2页浏览型号RS7302-285DLNNEP的Datasheet PDF文件第3页浏览型号RS7302-285DLNNEP的Datasheet PDF文件第4页浏览型号RS7302-285DLNNEP的Datasheet PDF文件第6页浏览型号RS7302-285DLNNEP的Datasheet PDF文件第7页浏览型号RS7302-285DLNNEP的Datasheet PDF文件第8页浏览型号RS7302-285DLNNEP的Datasheet PDF文件第9页  
页页次: 5/11
详细说明
该RS7302是一个低压差线性稳压器。该器件可提供预设的1.8V,2.5V和3.3V输出电压的输出
电流高达600mA 。特殊的输出电压等面膜的选择也可以。如所示的功能块
diagram, it consists of a 0.95V bandgap reference, an error amplifier, a P‐channel pass transistor and an internal feedback 
分压器。
 
The 0.95V bandgap reference is connected to the error amplifier, which compares this reference with the feedback voltage 
并且放大电压差。如果反馈电压低于基准电压时,所述传送晶体管栅极是
拉到低,这允许更多的电流传递到输出引脚,并增加输出电压。如果反馈电压
过高时,导通晶体管的栅极被向上拉,以减少输出电压。
 
输出电压是通过内部的电阻分压器连接到V反馈
OUT
 
引脚。其他模块包括一个
输出限流器,热传感器,并关断逻辑。
 
内部P沟道MOSFET
该RS7302拥有一个P沟道MOSFET晶体管。不像使用PNP调整晶体管类似的设计时,P沟道
MOSFET的不需要基极驱动,从而降低了静态电流。 PNP型监管机构也浪费了相当大的电流
dropout when the pass transistor saturates, and use high base‐drive currents under large loads. The RS7302 does not suffer 
这些问题,仅消耗60μA (典型值)电流消耗在重负载下,以及在降
条件。
 
使能功能
EN引脚启动以及停止稳压器。当EN引脚被切换到关闭电源电平,所有内部电路的动作
停止时,引脚V的积聚在P沟道MOSFET输出晶体管
IN
 
和V
OUT
 
关闭时,允许电流
消耗大幅度减少。在V
OUT
销进入到V之间的内部放电路径的GND电平
OUT
 
和GND引脚。
 
软启动功能
该电容可以连接之间的旁路引脚与GND 。该电容可以是一个低成本的聚酯薄膜品种。一
较大的电容,增强了交流纹波抑制,也使得输出拿出缓慢。这"Soft"开启希望
在一些应用中,以限制导通浪涌。
 
快速放电功能
该RS7302固定式对EN引脚禁用快速放电功能。当用户关闭该设备,其内部上拉低
电阻会放电输出电容充电。这将避免出现错误的议案等设备。
 
输出电压选择
For fixed voltage type of RS7302, the output voltage is preset at an internally trimmed voltage. The first two digits of part 
number suffix identify the output voltage (see Ordering Information). For example, the RS7302‐33 has a preset 3.3V output 
电压“。
 
电流限制
The RS7302 also includes a fold back current limiter. It monitors and controls the pass transistor’s gate voltage, estimates the 
output current, and limits the output current within 1.0A (Typ.) 
 
热过载保护
Thermal overload protection limits total power dissipation in the RS7302. When the junction temperature exceeds T
J
=+165°C, 
热传感器关断导通晶体管,使IC降温。热传感器接通传输晶体管
again after the junction temperature cools down by 20°C, resulting in a pulsed output during continuous thermal overload 
条件。
 
Thermal overload protection is designed to protect the RS7302 in the event of fault conditions. For continuous operation, the 
的T绝对最大工作结温额定值
J
=+125°C should not be exceeded. 
 
 
 
 
DS‐RS7302‐02 
   
September, 2009 
www.Orister.com