C8051F360/1/2/3/4/5/6/7/8/9
and each CALL pushes two record bits onto the register. (A POP or decrement SP pops one record bit,
and a RET pops two record bits, also.) The stack record circuitry can also detect an overflow or underflow
on the 32-bit shift register, and can notify the debug software even with the MCU running at speed.
9.4.6. Special Function Registers
The direct-access data memory locations from 0x80 to 0xFF constitute the special function registers
(SFR’s). The SFR’s provide control and data exchange with the CIP-51's resources and peripherals. The
CIP-51 duplicates the SFR’s found in a typical 8051 implementation as well as implementing additional
SFR’s used to configure and access the sub-systems unique to the MCU. This allows the addition of new
functionality while retaining compatibility with the MCS-51™ instruction set. Table 9.2 lists the SFR’s imple-
mented in the CIP-51 System Controller.
The SFR registers are accessed whenever the direct addressing mode is used to access memory loca-
tions from 0x80 to 0xFF. SFR’s with addresses ending in 0x0 or 0x8 (e.g. P0, TCON, P1, SCON, IE, etc.)
are bit-addressable as well as byte-addressable. All other SFR’s are byte-addressable only. Unoccupied
addresses in the SFR space are reserved for future use. Accessing these areas will have an indeterminate
effect and should be avoided. Refer to the corresponding pages of the data sheet, as indicated in
9.4.6.1. SFR Paging
The CIP-51 features
SFR paging,
allowing the device to map many SFR’s into the 0x80 to 0xFF memory
address space. The SFR memory space has 256
pages.
In this way, each memory location from 0x80 to
0xFF can access up to 256 SFR’s. The C8051F36x family of devices utilizes two SFR pages: 0 and F. SFR
pages are selected using the Special Function Register Page Selection register, SFRPAGE (see SFR Def-
1. Select the appropriate SFR page number using the SFRPAGE register.
2. Use direct accessing mode to read or write the special function register (MOV instruction).
9.4.6.2. Interrupts and SFR Paging
When an interrupt occurs, the SFR Page Register will automatically switch to SFR page 0, where all regis-
ters containing the interrupt flag bits are accessible. The automatic SFR Page switch function conveniently
removes the burden of switching SFR pages from the interrupt service routine. Upon execution of the RETI
instruction, the SFR page is automatically restored to the SFR Page in use prior to the interrupt. This is
accomplished via a three-byte
SFR Page Stack.
The top byte of the stack is SFRPAGE, the current SFR
Page. The second byte of the SFR Page Stack is SFRNEXT. The third, or bottom byte of the SFR Page
Stack is SFRLAST. On interrupt, the current SFRPAGE value is pushed to the SFRNEXT byte, and the
value of SFRNEXT is pushed to SFRLAST. Hardware then loads SFRPAGE with the SFR Page containing
the flag bit associated with the interrupt. On a return from interrupt, the SFR Page Stack is popped result-
ing in the value of SFRNEXT returning to the SFRPAGE register, thereby restoring the SFR page context
without software intervention. The value in SFRLAST (0x00 if there is no SFR Page value in the bottom of
the stack) of the stack is placed in SFRNEXT register. If desired, the values stored in SFRNEXT and SFR-
LAST may be modified during an interrupt, enabling the CPU to return to a different SFR Page upon exe-
cution of the RETI instruction (on interrupt exit). Modifying registers in the SFR Page Stack does not cause
a push or pop of the stack. Only interrupt calls and returns will cause push/pop operations on the SFR
Page Stack.
88
Rev. 1.0
SILABS [ SILICON LABORATORIES ]
