欢迎访问ic37.com |
会员登录 免费注册
发布采购

SC73C1402 参数 Datasheet PDF下载

SC73C1402图片预览
型号: SC73C1402
PDF下载: 下载PDF文件 查看货源
内容描述: 4BIT MCU用于遥控器(面罩式) [4BIT MCU FOR REMOTE CONTROLLER(MASK TYPE)]
分类和应用: 遥控远程控制遥控器
文件页数/大小: 19 页 / 374 K
品牌: SILAN [ SILAN MICROELECTRONICS JOINT-STOCK ]
 浏览型号SC73C1402的Datasheet PDF文件第2页浏览型号SC73C1402的Datasheet PDF文件第3页浏览型号SC73C1402的Datasheet PDF文件第4页浏览型号SC73C1402的Datasheet PDF文件第5页浏览型号SC73C1402的Datasheet PDF文件第7页浏览型号SC73C1402的Datasheet PDF文件第8页浏览型号SC73C1402的Datasheet PDF文件第9页浏览型号SC73C1402的Datasheet PDF文件第10页  
SC73C1402  
6. LR  
LR refers to the L register (4 bits). It is often used to store the pointer of RAM addresses, and can also be  
used as a general•purpose register.  
7. RAM  
RAM refers to data memory. It consists of 16 x 4bits and is used to store temporary data and results after a  
program is executed. There are two RAM addressing modes: one for indirect addressing by the LR register, it  
can address the entire RAM areas. The other is instruction direct addressing, the lower 3•bit of the instruction  
specifying the address of the RAM. It can be used to address the lower 8•bit of the RAM, but SC73C1402 does  
not support this mode. When reset, the contents of RAM are not defined. We recommend users to initialize it at  
the beginning of the program.  
8. ALU  
The arithmetic and logic unit plays a leading role in performing various operations of 4•bit binaries. The  
operation of the ALU will change the carry flag and the zero flag.  
9. Acc  
4•bit accumulator, it is mostly used to store data and results.  
10. CF  
CF refers to carry flag.  
11. SF  
SF refers to the status flag. When reset, the status flag is initialized to 1.  
12. PR  
PR refers to the port register, which specifies the input mode or output mode of the I/O ports, is 4•bit write•  
only. When one bit of PR is 1, the corresponding port is set to output mode; if the bit of PR is 0; then set to input  
mode. The execution of the HOLD instruction won’t affect the status of PORT1 and PORT2. When reset, the  
value of the PR is 0000B.  
P2S  
P1HS  
P1LS  
P11, P10 mode select  
P13, P12 mode select  
PORT2 mode select  
13. PORT  
SC73C1402 has five groups of I/O ports, altogether 20 pins.  
P0 port: P03~P00, 4•bit input port, with internal pull•down resistor; it can release the HOLD mode at high  
level.  
P1 port (P13~P10) and P2 port (P23~P20) can be set to input/output mode by program. In input mode, it  
can release HOLD mode at high level.  
P3 port (P30~P33) output port.  
P5 port (P53, P52, P51, P50)  
P50: output pin, P•channel open•drain output, this pin is always used to select system code.  
HANGZHOU SILAN MICROELECTRONICS CO.,LTD  
REV:1.1  
2005.12.19  
Http: www.silan.com.cn  
Page 6 of 20