欢迎访问ic37.com |
会员登录 免费注册
发布采购

S29AL016M10BFIR20 参数 Datasheet PDF下载

S29AL016M10BFIR20图片预览
型号: S29AL016M10BFIR20
PDF下载: 下载PDF文件 查看货源
内容描述: 16兆位(2M ×8位/ 1的M× 16位), 3.0伏只引导扇区闪存特色MirrorBit⑩技术 [16 Megabit (2 M x 8-Bit/1 M x 16-Bit) 3.0 Volt-only Boot Sector Flash Memory Featuring MirrorBit⑩ Technology]
分类和应用: 闪存
文件页数/大小: 62 页 / 1999 K
品牌: SPANSION [ SPANSION ]
 浏览型号S29AL016M10BFIR20的Datasheet PDF文件第35页浏览型号S29AL016M10BFIR20的Datasheet PDF文件第36页浏览型号S29AL016M10BFIR20的Datasheet PDF文件第37页浏览型号S29AL016M10BFIR20的Datasheet PDF文件第38页浏览型号S29AL016M10BFIR20的Datasheet PDF文件第40页浏览型号S29AL016M10BFIR20的Datasheet PDF文件第41页浏览型号S29AL016M10BFIR20的Datasheet PDF文件第42页浏览型号S29AL016M10BFIR20的Datasheet PDF文件第43页  
D a t a
S h e e t
Figure 8
shows the toggle bit algorithm in flowchart form, and the section
“Read-
ing Toggle Bits DQ6/DQ2”
explains the algorithm. See also the
DQ6: Toggle Bit I
subsection.
Figure 20
shows the toggle bit timing diagram.
Figure 21
shows the
differences between DQ2 and DQ6 in graphical form.
Reading Toggle Bits DQ6/DQ2
Refer to
Figure 8
for the following discussion. Whenever the system initially be-
gins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to
determine whether a toggle bit is toggling. Typically, the system would note
and store the value of the toggle bit after the first read. After the second read,
the system would compare the new value of the toggle bit with the first. If the
toggle bit is not toggling, the device has completed the program or erase op-
eration. The system can read array data on DQ7–DQ0 on the following read
cycle.
However, if after the initial two read cycles, the system determines that the toggle
bit is still toggling, the system also should note whether the value of DQ5 is high
(see the section on DQ5). If it is, the system should then determine again
whether the toggle bit is toggling, since the toggle bit may have stopped toggling
just as DQ5 went high. If the toggle bit is no longer toggling, the device has suc-
cessfully completed the program or erase operation. If it is still toggling, the
device did not complete the operation successfully, and the system must write
the reset command to return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit
is toggling and DQ5 has not gone high. The system may continue to monitor the
toggle bit and DQ5 through successive read cycles, determining the status as de-
scribed in the previous paragraph. Alternatively, it may choose to perform other
system tasks. In this case, the system must start at the beginning of the algo-
rithm when it returns to determine the status of the operation (top of
Figure 8).
October 11, 2006 S29AL016M_00_A7
S29AL016M
37