欢迎访问ic37.com |
会员登录 免费注册
发布采购

ST62T01CM6/TR 参数 Datasheet PDF下载

ST62T01CM6/TR图片预览
型号: ST62T01CM6/TR
PDF下载: 下载PDF文件 查看货源
内容描述: 8位微控制器( MCU)和OTP 。只读存储器。 FASTROM 。 EPROM 。 A / D转换器。振荡器保障。国家外汇管理局复位和16针\n [8-BIT MICROCONTROLLER (MCU) WITH OTP. ROM. FASTROM. EPROM. A/D CONVERTER. OSCILLATOR SAFEGUARD. SAFE RESET AND 16 PINS ]
分类和应用: 振荡器转换器存储微控制器可编程只读存储器电动程控只读存储器
文件页数/大小: 100 页 / 969 K
品牌: STMICROELECTRONICS [ ST ]
 浏览型号ST62T01CM6/TR的Datasheet PDF文件第9页浏览型号ST62T01CM6/TR的Datasheet PDF文件第10页浏览型号ST62T01CM6/TR的Datasheet PDF文件第11页浏览型号ST62T01CM6/TR的Datasheet PDF文件第12页浏览型号ST62T01CM6/TR的Datasheet PDF文件第14页浏览型号ST62T01CM6/TR的Datasheet PDF文件第15页浏览型号ST62T01CM6/TR的Datasheet PDF文件第16页浏览型号ST62T01CM6/TR的Datasheet PDF文件第17页  
ST6200C/ST6201C/ST6203C  
MEMORY MAP (Cont’d)  
3.1.6.2 Data ROM Window memory addressing  
tion is automatically handled by the ST6 develop-  
ment tools.  
In cases where some data (look-up tables for ex-  
ample) are stored in program memory, reading  
these data requires the use of the Data ROM win-  
dow mechanism. To do this:  
Please refer to the user manual of the correspod-  
ing tool.  
3.1.6.3 Recommendations  
1. The DRWR register has to be loaded with the  
64-byte block number where the data are located  
(in program memory). This number also gives the  
start address of the block.  
Care is required when handling the DRWR regis-  
ter as it is write only. For this reason, the DRWR  
contents should not be changed while executing  
an interrupt service routine, as the service routine  
cannot save and then restore the register’s previ-  
ous contents. If it is impossible to avoid writing to  
the DRWR during the interrupt service routine, an  
image of the register must be saved in a RAM lo-  
cation, and each time the program writes to the  
DRWR, it must also write to the image register.  
The image register must be written first so that, if  
an interrupt occurs between the two instructions,  
the DRWR is not affected.  
2. Then, the offset address of the byte in the Data  
ROM Window (corresponding to the offset in the  
64-byte block in program memory) has to be load-  
ed in a register (A, X,...).  
When the above two steps are completed, the  
data can be read.  
To understand how to determine the DRWR and  
the content of the register, please refer to the ex-  
ample shown in Figure 6. In any case the calcula-  
Figure 6. Data ROM Window Memory Addressing  
DATA SPACE  
000h  
PROGRAM SPACE  
0000h  
040h  
OFFSET  
21h  
DATA  
061h  
07Fh  
0400h  
64 bytes  
OFFSET  
0421h  
DATA  
DRWR  
0FFh  
10h  
07FFh  
DATA address in Program memory : 421h  
DRWR content : 421h / 3Fh (64) = 10H data is located in 64-bytes window number 10h  
64-byte window start address : 10h x 3Fh = 400h  
Register (A, X,...)content : Offset = (421h - 400h) + 40h ( Data ROM Window start address in data space) = 61h  
13/100  
1