SMS64
Preliminary
ABSOLUTE MAXIMUM RATINGS
Temperature Under Bias ...................... -55
°
C to 125
°
C
Storage Temperature............................ -65
°
C to 150
°
C
Terminal Voltage with Respect to GND:
VCC
A
, VCC
B
, VCC
C
, VCC
D
, VCC
E
, VCC
F
..-0.3V to 6.0V
VM
A
, VM
B
, VM
C
, VM
D
, VM
E
, VM
F
...............-0.3V to 6.0V
PUP
A
, PUP
B
, PUP
C
, PUP
D,
PUP
E
, PUP
F
.............. 15.5V
All Others ......................................................V
CC
+ 0.7V
Output Short Circuit Current ............................... 100mA
Lead Solder Temperature (10 secs) .................... 300
°
C
ESD Rating per JEDEC…………………………..2000V
Latch-Up testing per JEDEC……………......+/- 100mA
RECOMMENDED OPERATING CONDITIONS
Temperature Range(Ambient)...……-40
°
C to +85
°
C
Supply Voltage………………….………2.7V to 6.0V
1/
Package Thermal Resistance (θ JA)
48 Lead SSOP…………………………………80
o
C/W
Moisture Classification Level 1 (MSL 1) per J-STD- 020
RELIABILITY CHARACTERISTICS
Data Retention…………………………..…..100 Years
Endurance…………………….……….100,000 Cycles
Stresses listed under Absolute Maximum Ratings may cause permanent
damage to the device. These are stress ratings only and functional operation
of the device at these or any other conditions outside those listed in the
operational sections of the specification is not implied. Exposure to any
absolute maximum rating for extended periods may affect device performance
and reliability.
Devices are ESD sensitive. Handling precautions are
recommended.
DC OPERATING CHARACTERISTICS
(Over recommended operating conditions, unless otherwise noted. All voltages are relative to GND.)
Symbol
Parameter
Notes
Min.
Typ.
Max
Device supply voltage
Supply Voltage VCC
A
, VCC
B
, VCC
C,
defined by the highest of
2.7
6.0
VCC
VCC
D,
VCC
E,
VCC
F
the six VCC inputs. Must
be > 2.7V. – Note 1/
Active Current with PUP
I
DD
(ON)
2
Outputs configured as
Power Supply Current
high-side drivers enabled
Quiescent Current high-
1
I
DD
(Off)
side PUP Outputs disabled
Programmable Threshold (VCC and VM
P
VIT
8-bit resolution 20mV/bit
0.9
6.0
Inputs)
“naked” mode, V input
V
TH
Fixed threshold Voltage
0.5
disconnected from ground
PUP characteristics when configured as high-side driver
Option 1 (MOSFETs on)
14.5
P
VPUP
Programmable PUP Output
Option 2 (MOSFETs on)
10.5
V
PUP
OFF PUP Output
I
PUPSINK
= 2mA
0
0.4
When configured as high-
I
PUP
PUP Drive Current
8
side driver and with
MOSFET switches on
When Configured as High
SR
PUP
PUP Slew Rate
250
Side Driver
PUP characteristics when configured as a logic output
V
OL
Output Low Voltage
All other input and output characteristics
Input High Voltage (FS#, PWR_ON/OFF,
V
IH
MR#)
Input Low Voltage (FS#, PWR_ON/OFF,
V
IL
MR#)
Open Drain Outputs (RST_A#, RST_B#,
V
OL
IRQ#, HEALTHY#)
I
SINK
= 2mA
VCC = 2.7V
VCC = 5.0V
VCC = 2.7V
VCC = 5.0V
I
SINK
= 2mA
0
0.9xVI
0.7xVI
Unit
V
mA
mA
V
V
V
V
V
µA
V/s
0.4
VI
VI
0.1xVI
0.3xVI
V
V
V
V
V
V
-0.1
-0.1
0
0.4
Notes: 1/ At least one of the VCC inputs needs to be at or above 2.7V for proper device operation.
Summit Microelectronics, Inc
2060 2.22 10/09/03
7
SUMMIT [ SUMMIT MICROELECTRONICS, INC. ]
