08ꢀ&ꢁꢂꢃꢁ/ꢄ4XDGꢄꢅꢆꢇꢅꢆꢆ0Eꢄ(WKHUQHWꢄ)LOWHUꢄ,QWHUIDꢈH
3LQꢄ'HVꢈULSWLRQV
ꢌ&0ꢀ>/$1&$0ꢀ%XVꢀ&RPPDQGꢀ0RGHꢁꢀ2XWSXWꢁꢀ
7ULꢒVWDWHꢁꢀ77/?
$UELWUDWLRQꢀ%XV
6<1&ꢀ>,QSXWꢌ2XWSXWꢁꢀ77/?
The MU9C8358L outputs /CM Data/Command Select to
control whether the LANCAM interprets the DQ[15:0]
bus contents as command information or data. If both /CM
and /W are LOW at the falling edge of /E, the
MU9C8358L outputs an instruction for the LANCAM to
execute or a value for one of the LANCAM configuration
registers. If /CM is LOW while /W is HIGH, then the
LANCAM will output data from one of its configuration
registers to the MU9C8358L. If /CM is HIGH while /W is
LOW, the MU9C8358L will output data for the LANCAM
to place in one of its data registers or memory. If /CM is
HIGH while /W is HIGH, the LANCAM outputs data
from one of its data registers or memory to the
MU9C8358L.
The MU9C8358L configured as MASTER provides this
signal as an output. An MU9C8358L configured as a SLAVE
uses this signal as input. This signal is not used in a single
MU9C8358L application and may be left unconnected. This
pin has a 50-kΩ internal pull-up resistor. See Timing
Diagrams: Timing Data for Control Interfaces.
$5%ꢐꢄꢑꢆ@ꢀ>$UELWHUꢀ3RUWꢁꢀ,QSXWꢌ2XWSXWꢁꢀ77/?
The MU9C8358L configured as MASTER must monitor the
attached slave device to determine which device gains access
to the CAM in a given processing cycle. These signals are
not used in a single MU9C8358L application, and may be
left unconnected. These pins have 50-kΩ internal pull-up
resistors. See Timing Diagrams: Timing Data for Control
Interfaces.
ꢌ(&ꢀ>/$1&$0ꢀ%XVꢀ(QDEOHꢀ&KDLQꢁꢀ2XWSXWꢁꢀ
7ULꢒVWDWHꢁꢀ77/?
-7$*
The Daisy Chain Enable signal performs two functions.
The /EC signal enables the LANCAMs /MF output to
show the results of a comparison. If /EC is LOW at the
falling edge of /E in a cycle, the /MF flag output is
enabled; otherwise, /MF is held HIGH. The /EC signal
also enables the /MF-/MI daisy chain that serves to select
the device with the highest-priority match in a string of
LANCAMs.
Please refer to IEEE Standard 1149.1 for information on
using the mandatory JTAG functions. The optional HIGH-Z
function is implemented and may be activated by writing
0011 to the JTAG Instruction register.
ꢌ7567ꢀ>-7$*ꢀ5HVHWꢁꢀ,QSXW?
The /TRST is the Test Reset pin. It is internally pulled up
with a 50-kΩresistor. It must be tied to /RESET or tied LOW
when the JTAG port is not used.
ꢌ0,ꢀ>/$1&$0ꢀ%XVꢀ0DWꢂKꢀ)ODJꢁꢀ,QSXWꢁꢀ77/?
7&.ꢀ>-7$*ꢀ7HVWꢀ&ORꢂNꢁꢀ,QSXW?
The TCK input is the Test Clock input. It can be tied at a
valid logic level 1 when not in use. This pin is internally
The /MI LANCAM Match flag input is used to indicate to
the MU9C8358L the conditions of the LANCAM Match
flag. The /MF output from the LANCAM should be
connected to this pin. If more than one LANCAM is used,
/MI should be connected to the /MF pin of the last
LANCAM in the daisy chain.
pulled up with a 50-kΩresistor.
706ꢀ>-7$*ꢀ7HVWꢀ0RGHꢀ6HOHꢂWꢁꢀ,QSXW?ꢀ
The TMS input is the Test Mode Select input. This pin is
internally pulled up with a 50-kΩ resistor.
ꢌ),ꢀ>/$1&$0ꢀ%XVꢀ)XOOꢀ)ODJꢁꢀ,QSXWꢁꢀ77/?
The /FI LANCAM Full flag input is used to indicate to the
MU9C8358L the condition of the LANCAM Full flag.
The /FF output from the LANCAM should be connected
to this pin. If more than one LANCAM is used, /FI should
be connected to the /FF of the last device in the daisy
chain.
7',ꢀ>-7$*ꢀ7HVWꢀ'DWDꢀ,QSXWꢁꢀ,QSXW?ꢀ
The TDI input is the Test Data input. This pin is internally
pulled up with a 50-kΩ resistor.
7'2ꢀ>-7$*ꢀ7HVWꢀ'DWDꢀ2XWSXWꢁꢀ2XWSXW?ꢀ
The TDO output is the Test Data output.
7(67(1
This pin is used for internal MUSIC Semiconductor testing
ꢌ5(6(7B/&ꢀ>5HVHWꢀ/$1&$0ꢁꢀ2XWSXWꢁꢀ77/?ꢀ>6ODYHꢀ
,QVWDQꢂHꢀꢒꢀ1Rꢀ&RQQHꢂWLRQ?
only. This pin has a 50-k
be left as "NO CONNECT" in system applications.
Ω pull-up resistor to VDD and may
/RESET_LC is LOW whenever /RESET is LOW. It is
taken HIGH only by writing to bit 0 in the System
Dynamic Configuration (SDCFG) register. See SDCFG
register information. /RESET_LC is used only on the
master device; it is left unconnected on the slave device
when two MU9C8358Ls are connected together.
3RZHUꢀ$QGꢀ*URXQG
9''ꢀꢁ*1'ꢁꢂ3RVLWLYHꢁ3RZHUꢁ6XSSO\ꢀꢁ*URXQGꢃ
These pins are the power supply connections to the
MU9C8358L. VDD must meet the voltage supply
requirements in the Operating Conditions section relative to
the GND pins, which are at 0 Volts (system reference
potential), for correct operation of the device.
ꢉ
5HYꢇꢀꢄ
MUSIC [ MUSIC SEMICONDUCTORS ]
