OPA361AQDCKRQ1全新原装原理图各脚功能电路原理芯片引脚定义-中国IC网-芯三七

当前位置：IC37首页_>O字母起始型号索引_>O字母起始型号索引第42页更新时间：2024-10-25 17:21:16

产品型号OPA361AQDCKRQ1的概述

OPA361AQDCKRQ1芯片概述 OPA361AQDCKRQ1是一款高性能的运算放大器，属于德州仪器（Texas Instruments）公司的产品系列。该芯片专为低功耗和高带宽应用而设计，适合在音频和信号处理领域的多种应用。其典型特性使其能够在多种环境下实现高精度信号处理，特别是在需要低失真和高增益稳定性的场合。 OPA361AQDCKRQ1具有低输入偏置电流、低噪声和宽动态范围等优点，适合用于医疗仪器、便携式设备和音频放大器等应用。因此，它成为了电子工程师和设计师在选择运算放大器时的热门选择。详细参数 1. 电源电压范围：OPA361AQDCKRQ1支持宽电源电压范围，通常在3V到36V之间，适应不同应用场景的需求。 2. 增益带宽产品：该芯片的增益带宽产品为20MHz，适合一定频率范围内的信号处理。 3. 输入失调电压：OPA361AQDCKRQ1具有极低的输入失调...

产品型号OPA361AQDCKRQ1的Datasheet PDF文件预览

OPA361-Q1

www.ti.com

SBOS552 –MARCH 2011

3V Video Amplifier with Internal Gain and Filter in SC70

Check for Samples: OPA361-Q1

FEATURES

DESCRIPTION

The OPA361-Q1 high-speed amplifier is optimized for

3V portable video applications. It is specifically

designed to be compatible with the video encoders

embedded in Texas Instruments’ OMAP2420 and

DaVinci processors or other application processors

with 0.5V_PPvideo output. The input common-mode

range includes GND, which allows a video-DAC

(digital-to-analog converter) to be DC-coupled to the

OPA361-Q1. The TV-detection feature simplifies the

end-user interface significantly by facilitating the

automatic start/stop of video transmission.

•

Qualified for Automotive Applications

Excellent Video Performance

Internal Gain: 5.2V/V

Supports TV-Detection

Compatible with OMAP242x and

DAVINCI™ Processors

•

2-Pole Reconstruction Filter

Input Range Includes Ground

–

DC-Coupled Input

The output swings within 5mV of GND and 250mV to

V+ with a standard back-terminated video load

(150Ω). An internal level shift circuit prevents the

output from saturating with 0V input, thus preventing

sync-pulse clipping in common video circuits.

Therefore, the OPA361-Q1 is ideally suited for

DC-coupling to the video load.

•

Integrated Level Shifter

–

DC-Coupled Output⁽¹⁾

No Output Capacitors Needed

•

Rail-to-Rail Output

Low Quiescent Current: 5.3mA

Shutdown Current: 1.5µA

Single-Supply: 2.5V to 3.3V

SC70-6 Package: 2.0mm × 2.1mm

RoHS Compliant

The OPA361-Q1 has

been optimized for

space-sensitive applications by integrating internal

gain setting resistors (G = 5.2V/V) and a 2-pole

video-DAC reconstruction filter.

•

(1)

In shutdown mode, the quiescent current is reduced

to < 1.5µA, dramatically reducing power consumption

and prolonging battery life.

Internal circuitry avoids output saturation, even with 0V sync

tip level at the input video signal.

V+

The OPA361-Q1 is available in the tiny 2mm ×

2.1mm SC70-6 package.

OPA361

10mV

2-Pole

+In

75Ω

Filter

Out

Ω

500

R_SET

Ω

G =5.2V/V

Shutdown

Control

(see note 1)

Enable

GND

(1) Closed when enabled during normal

operation; open when shut down.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

OPA361-Q1

SBOS552 –MARCH 2011

www.ti.com

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

ORDERING INFORMATION⁽¹⁾

PRODUCT

PACKAGE

PACKAGE DESIGNATOR

PACKAGE MARKING

OPA361-Q1

SC70-6

DCK

QXP

(1) For the most current package and ordering information, see the Package Option Addendum at the end of this datasheet, or see the TI

website at www.ti.com.

PIN CONFIGURATION

DCK PACKAGE

(TOP VIEW)

GND

R_SET

V+

Enable

Out

The location of pin 1 on the OPA361-Q1 is determined by orienting the package marking as shown in the diagram

above.

ABSOLUTE MAXIMUM RATINGS⁽¹⁾

VALUE

UNIT

Supply voltage, V+ to V–

+3.6

–0.5 to (V+) + 0.5

±10

Voltage⁽²⁾

Current⁽²⁾

Signal input terminals

Output short-circuit through 75Ω to GND⁽³⁾

Continuous

–40 to +125

–65 to +150

+160

Operating temperature

°C

Storage temperature

Junction temperature

(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may

degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond

those specified is not implied.

(2) Input terminals are diode-clamped to the power-supply rails. Input signals that can swing more than 0.5V beyond the supply rails should

be current-limited to 10mA or less.

(3) Short-circuit to ground.

Submit Documentation Feedback

Product Folder Link(s) :OPA361-Q1

OPA361-Q1

www.ti.com

SBOS552 –MARCH 2011

ELECTRICAL CHARACTERISTICS: V_S= +2.5V to +3.3V

Boldface limits apply over the temperature range, T_A= –40°C to +125°C.

At T_A= +25°C, R_L= 150Ω connected to GND, unless otherwise noted.

PARAMETER

TEST CONDITIONS

MIN

TYP MAX

UNIT

OFFSET LEVEL-SHIFT VOLTAGE

V_OLS

Output Level-Shift Voltage⁽¹⁾

V_S= +2.8V, V_IN= GND

V_S= +2.5V to +3.3V

–3

Over Temperature

PSRR

vs Power Supply

±80

µV/V

INPUT VOLTAGE RANGE

V_S= 2.5V

V_S= 2.8V

V_S= 3.3V

GND

450

0.42

0.48

0.55

550

V_CM

Input Voltage Range⁽²⁾

R_IN

Input Resistance (+In)

R_SETResistance

510

R_SET

3600 4070 4400

2% 0.5%

Matching of R_INand R_SET

VOLTAGE GAIN

ΔV_OUT/ΔV_IN, V_S= +2.5V, V_INMIN= 0V, V_INMAX= 0.42V

ΔV_OUT/ΔV_IN, V_S= +2.8V, V_INMIN= 0V, V_INMAX= 0.48V

ΔV_OUT/ΔV_IN, V_S= +3.3V, V_INMIN= 0V, V_INMAX= 0.55V

5.06

5.17

5.28

V/V

FREQUENCY RESPONSE

Filter Response

f−3dB

Cutoff Frequency

Normalized Gain:

–0.1

–18

–23

1.2%

1.6

MHz

f_IN= 4.5MHz

f_IN= 27MHz

f_IN= 54MHz

V_O= 2V_PP

Differential Gain Error

Differential Phase Error

Group Delay Variation

Signal-to-Noise Ratio

R_L= 150Ω

degrees

100kHz, 4.5MHz

100% White Signal

SNR

OUTPUT

Positive Voltage Output Swing from Rail

Negative Voltage Output Swing from Rail

Positive Voltage Output Swing from Rail

Negative Voltage Output Swing from Rail

Output Leakage

V_S= +2.8V, V_IN= 0.7V,Ω to GND

V_S= +2.8V, V_IN= –0.05V, R_L= 150Ω to GND

V_S= +2.8V, V_IN= 0.7V, R_L= 75Ω to GND

V_S= +2.8V, V_IN= –0.05V, R_L= 75Ω to GND

V_S= +2.8V, Disabled, V_O= 2V

130

0.15

260

250

0.3

±80

100

I_O

Output Current⁽³⁾

V_S= +2.8V

POWER SUPPLY

V_S

I_Q

Specified Voltage Range

2.5

3.3

7.5

Quiescent Current

V_S= +2.8V, Enabled, I_O= 0, V_OUT= 1.4V

5.3

Over Temperature

Specified Temperature Range

ENABLE/SHUTDOWN FUNCTION

Disabled (logic-LOW threshold)

Enabled (logic-HIGH threshold)

Enable Time

0.35

V_S

1.3

1.5

µs

µA

Disable Time

Shutdown Current

V_S= +2.8V, Disabled

1.5

TEMPERATURE RANGE

Specified/Operating Range

Storage Range

–40

–65

+125

+150

°C

θ_JA

Thermal Resistance

SC70

250

°C/W

(1) Output referred.

(2) Limited by output swing and internal G = 5.2V/V.

(3) See typical characteristics Output Voltage Swing vs Output Current.

Submit Documentation Feedback

Product Folder Link(s) :OPA361-Q1

OPA361-Q1

SBOS552 –MARCH 2011

www.ti.com

TYPICAL CHARACTERISTICS: V_S= 2.8 V

At T_A= +25°C and R_L= 150, unless otherwise noted.

R_IN

R_SET

TEMPERATURE

535

530

525

520

515

510

505

500

495

4250

4200

4150

4100

4050

4000

3950

−

150

−

+25

+50

+75 +100 +125 +150

100 +125

Temperature (°C)

R_SET/R_INRATIO

GAIN

TEMPERATURE

8.5

5.5

5.4

5.3

5.2

5.1

5.0

8.4

8.3

8.2

8.1

8.0

7.9

7.8

7.7

7.6

7.5

−

+25

+50

+75

+100 +125 +150

+25

+50

+75 +100 +125 +150

Temperature (°C)

OUTPUT VOLTAGE

TEMPERATURE

0.005

0.004

0.003

0.002

0.001

2.80

2.75

2.70

2.65

2.60

2.55

2.50

V_IN= 700mV

V_S= 2. 8V

−

= 50mV

V_IN

V_S= 2. 8V

−

+25

+50

+75 +100 +125 +150

+25

+50

+75 +100 +125 +150

Temperature (°C)

Submit Documentation Feedback

Product Folder Link(s) :OPA361-Q1

OPA361-Q1

www.ti.com

SBOS552 –MARCH 2011

TYPICAL CHARACTERISTICS: V_S= 2.8 V (continued)

At T_A= +25°C and R_L= 150, unless otherwise noted.

V_OUTLEVEL SHIFT

QUIESCENT CURRENT

TEMPERATURE

0.05

V_S= 2. 8V

V_IN= 0V

0.04

0.03

0.02

0.01

−

0.01

−

+25

+50

+75 +100 +125 +150

+25

+50

+75 +100 +125 +150

Temperature (°C)

OUTPUT LEAKAGE CURRENT

OUTPUT LEAKAGE

TEMPERATURE

IN SHUTDOWN

1000000

100000

10000

1000

100

400

350

300

250

200

150

100

Enable =0V

V_PULLUP= 1. 8V

−

0.1

100

0.5

1.5

2.5

−

+25

+50

+75 +100 +125 +150

V_PULLUP(V)

Temperature (°C)

SHUTDOWN QUIESCENT CURRENT HYSTERESIS

AC RESPONSE

TEMPERATURE

AT VARIOUS TEMPERATURES

10000

−

1000

100

−

40 C

−

+125

−

+25

+125

+85

+25

−

0.7

0.75

0.8

0.85

V_SHDN(V)

0.9

0.95

100k

10M

100M

Frequency (Hz)

Submit Documentation Feedback

Product Folder Link(s) :OPA361-Q1

OPA361-Q1

SBOS552 –MARCH 2011

www.ti.com

TYPICAL CHARACTERISTICS: V_S= 2.8 V (continued)

At T_A= +25°C and R_L= 150, unless otherwise noted.

TURN−ON TIME

TURN−OFF TIME

Time (1ms/div)

Time (25ns/div)

OUTPUT VOLTAGE

GROUP DELAY

OUTPUT CURRENT

FREQUENCY

3.0

2.5

2.0

1.5

1.0

100

−

+125

+85 C +25 C 0 C

0.5

100k

Frequency (Hz)

10M

100M

I_OUT(A)

DIFFERENTIAL GAIN

−

INP

SYNC

INT

MTIME

10s

LINE = 330

−

DG1

DG2

DG3

DG4

DG5

0.6

1.0

1.1

1.2

0.8

STEPS

ZOOM

MODE

DIFFERENTIAL PHASE

−

SYNC

INT

MTIME

10s

LINE

330

−

DP1

DP2

DP3

DP4

DP5

1.1

dg1

dg.

dg5

1.6

1.5

1.1

STEPS

ZOOM

MODE

Submit Documentation Feedback

Product Folder Link(s) :OPA361-Q1

OPA361-Q1

www.ti.com

SBOS552 –MARCH 2011

APPLICATION INFORMATION

The OPA361-Q1 video amplifier has been optimized to fit seamlessly with Texas Instruments’ OMAP242x

Multimedia processor. The following features have been integrated to provide excellent video performance.

•

Internal gain setting resistors (G = 5.2V/V) reduce the number of external components needed in the video

circuit.

Integration of the 500Ω video encoder load resistor and 4kΩ RSET resistor used by the OMAP242x helps

minimize the number of external components and also ensures excellent ratio and temperature tracking. This

feature helps to keep the overall gain accurate and stable over temperature.

•

TV-detection support in connection with an OMAP242x multimedia processor. This feature helps to automate

start/stop operation of the TV-out function and minimizes power consumption.

•

A 2-pole filter is incorporated for DAC signal reconstruction.

The OPA361-Q1 employs an internal level shift circuit that avoids sync pulse clipping and allows DC-coupled

output.

•

A shutdown feature reduces quiescent current to less than 1.5µA—crucial for portable applications

Although OPA361-Q1 is optimized for the OMAP242x processor, it is also suitable to interface with any digital

media processor that outputs a video signal on the order of 0.4V_PPto 0.5V_PP

Figure 1 shows a typical application drawing with the OMAP242x processor and the TWL92230 Energy

Management Chip.

TWL92230

1.8V DAC

0.5V V_REF

Regulator V_AUX

2.8V

V+

1.8V

OMAP2420

OPA361

PullUp

10kΩ

10mV

+In

Video

DAC

2-Pole

Filter

Ω

Out

500Ω

4kΩ

75Ω

R_SET

G =5.2V/V

Enable

Shutdown

Control

(see note 1)

TV Detect

GPIO⁽³⁾

GND

100kΩ⁽²⁾

TV Detect

GPIO

Figure 1. Typical Application using the OMAP242x and the TWL92230

Submit Documentation Feedback

Product Folder Link(s) :OPA361-Q1

OPA361-Q1

SBOS552 –MARCH 2011

www.ti.com

OPERATING VOLTAGE

The OPA361-Q1 is fully specified from 2.5V to 3.3V over a temperature range of –40°C to +125°C. Parameters

that vary significantly with operating voltages or temperature are shown in the Typical Characteristics.

Power-supply pins should be bypassed with 100nF ceramic capacitors.

INPUT VOLTAGE

The input common-mode range of the OPA361-Q1 series extends from GND to 0.55V on a 3.3V supply. The

input range is limited by the internal gain in conjunction with the maximum output swing capability and the

power-supply voltage.

INPUT OVERVOLTAGE PROTECTION

All OPA361-Q1 pins are static-protected with internal ESD protection diodes connected to the supplies. These

diodes will provide input overdrive protection if the current is externally limited to 10mA.

ENABLE/SHUTDOWN

The OPA361-Q1 has a shutdown feature that disables the output and reduces the quiescent current to less than

1.5µA. This feature is especially useful for portable video applications, where the device is infrequently

connected to a television (TV) or other video device.

The Enable logic input voltage is referenced to the OPA361-Q1 GND pin. A logic level HIGH applied to the

enable pin enables the op amp. The logic levels are compatible with 1.8V CMOS logic levels. A valid logic HIGH

is defined as > 1.3V above GND. A valid logic LOW is defined as < 0.35V above GND. If the Enable pin is not

connected, internal pull-up circuitry will enable the amplifier.

When disabling the OPA361-Q1, internal circuitry also disconnects the internal gain setting feedback. This

feature is in support of the TV-detection function. See the TV-Detect Function section for more detailed

information.

INTERNAL 2-POLE FILTER

The OPA361-Q1 filter is a Sallen-Key topology with a 9MHz cutoff frequency. Figure 2 shows a detailed drawing

of the filter components. This filter allows video signals to pass without any visible distortion, as shown in

Figure 3 through Figure 6. The video encoder embedded in the OMAP242x processor typically samples at

54MHz. At this frequency, the attenuation is typically 23dB, which effectively attenuates the sampling aliases.

The internal 500Ω resistor on the input to GND converts the output current of the OMAP2420 internal video DAC

into a voltage. It is also part of the Sallen-Key filter. Using an external resistor to adjust the input voltage range

will also alter the filter characteristics.

3.6pF

OPA361

Television

2.2kΩ

(

)

Ω

V_O

Ω

500

12.5pF

Ω

4.22kΩ

Ω

Figure 2. Filter Structure of the OPA361-Q1

Submit Documentation Feedback

Product Folder Link(s) :OPA361-Q1

OPA361-Q1

www.ti.com

SBOS552 –MARCH 2011

Video Performance

The color bar signal in Figure 3 shows excellent amplitude characteristics and no attenuation of colors with

respect to the luminance signal.

∆

: 2.02V

@: 30.0mV

Figure 3. 100/75 Color Bar Signal at Output of OPA361-Q1

The CCIR330/5 test pattern requires one of the greatest dynamic ranges, and therefore tests the OPA361-Q1

output voltage swing capability. The scope plot shown in Figure 4 has been taken with a 2.8V supply and shows

no clipping on the top side of the signal.

∆

: 2.30V

@: 2.31mV

Figure 4. CCIR330/5: No Clipping, Even On 2.8V Supply

The multiburst test patterns have different sine-wave burst sections with the following frequencies: 0.5MHz,

1MHz, 2MHz, 4MHz, 4.8MHz and 5.8MHz with 420mVPP. There is no visible attenuation even at the highest

frequencies, which indicates a very flat frequency response of the OPA361-Q1. As shown in Figure 5 and

Figure 6, the top line illustrates the full signal and the bottom line is a more detailed view of the last three sine

wave bursts.

Submit Documentation Feedback

Product Folder Link(s) :OPA361-Q1

OPA361-Q1

SBOS552 –MARCH 2011

www.ti.com

Figure 5. Multiburst Signal (CCIR 18/1) Shows Very Flat Frequency Response

The CCIR17 test pattern contains a 2T and a 20T pulse, as shown in Figure 6. The 2T pulse is used to check for

pulse distortion and reflection, and the 20T pulse is used to check for amplitude and group delay between

chrominance and luminance. Neither pulse exhibits any distortion or group delay artifacts.

Figure 6. CCIR 17 2T and 20T Pulses Show No Visible Distortion

INTERNAL LEVEL SHIFT

Many common video DACs embedded in digital media processors, like the new OMAP242x processors, operate

on a single supply (no negative supply). Typically, the lowest point of the sync pulse output by these video DACs

is close to 0V. With a 0V input, the output of a common single-supply op amp saturates at a voltage > 0V. This

effect would clip the sync pulse, and therefore degrade the video signal integrity. The OPA361-Q1 employs an

internal level shift circuit to avoid clipping. The input signal is typically shifted by approximately 11mV. This shift

is well within the linear output voltage range of the OPA361-Q1 with a standard 150Ω video load.

Output Swing Capability

Figure 7 shows the true output swing capability of the OPA361-Q1 by taking the tip of the input sync pulse to a

slightly negative voltage. Even when the output sync tip is at 3mV, the output after the 75Ω series termination still

shows no clipping of the sync pulse.

Submit Documentation Feedback

Product Folder Link(s) :OPA361-Q1

OPA361-Q1

www.ti.com

SBOS552 –MARCH 2011

∆

: 305mV

@: 3.00mV

Figure 7. No Clipping of the Sync Pulse

TV-Detect Function

The TV-detection feature of the OPA361-Q1 works in conjunction with the OMAP242x (or other processors) to

detect if a television is connected to the video output of the device. In order to detect a TV load, the OPA361-Q1

is briefly turned off, ideally during the first vertical sync pulse. For the detection, a simple pull-up resistor to the

processor logic supply is used on the output of the OPA361-Q1. The voltage level is pulled LOW if the TV (or

other video equipment) is connected, or HIGH if nothing is connected. A GPIO in the processor can be used to

read this logic level and decide if a video load is connected. Figure 8 shows a scope plot with the TV

disconnected and Figure 9 shows a scope plot with the TV connected; the upper line in both figures is the

disable pulse. Figure 10 shows a circuit drawing using the TV-detect signal to disable or enable the OPA361-Q1.

OPA361 Disable Pulse

∆

: 1.84V

@: 1.84V

OPA361 Ouput

Pulled HIGH;

No Video Load

Connected

1st Vertical Sync Pulse

Vertical Sync Pulses

Equilization Pulses

Figure 8. Output of OPA361-Q1 Pulled Up To 1.8V During Disable: TV Disconnected

Submit Documentation Feedback

Product Folder Link(s) :OPA361-Q1

OPA361-Q1

SBOS552 –MARCH 2011

www.ti.com

OPA361 Disable Pulse

OPA361 Ouput Pulled LOW

Due to Video Load

1st Vertical Sync Pulse

Vertical Sync Pulses

Equilization Pulses

Figure 9. Output of OPA361-Q1 Pulled Down: TV Connected.

TWL92230

1.8V DAC 0.5V V_REF

Regulator V_AUX

2.5Vor 2.8V

V+

1.8V

OMAP2420

OPA361

PullUp

10kΩ

10mV

+In

Video

DAC

2-Pole

Filter

Ω

Out

500Ω

4kΩ

75Ω

R_SET

G =5.2V/V

Enable

Shutdown

Control

(see note 1)

TV Detect

GPIO⁽³⁾

GND

Ω⁽²⁾

100k

TV Detect

GPIO

Figure 10. Using TV-Detect Signal to Disable/Enable the OPA361-Q1

Disabling the OPA361-Q1 also disconnects the internal feedback resistors’ path to GND, and therefore there is

no current flowing from the logic supply through the pull-up resistor to GND if no video load is connected; this

helps to conserve battery life. The typical leakage when the output is pulled high and OPA361-Q1 is disabled is

only about 300pA.

The following functionality can be achieved by implementing TV-detection:

•

Automatic video start by polling the video line periodically.

Automatic video stop if the TV (or other equipment) is disconnected.

Proper implementation allows to significantly simplify the user interface.

For more information, see Application Report SBOA109, OPA361-Q1 and TV Detection, available for download

at www.ti.com.

Submit Documentation Feedback

Product Folder Link(s) :OPA361-Q1

PACKAGE OPTION ADDENDUM

www.ti.com

30-Mar-2011

PACKAGING INFORMATION

Status ⁽¹⁾

Eco Plan ⁽²⁾

MSL Peak Temp ⁽³⁾

Samples

Orderable Device

Package Type Package

Drawing

Pins

Package Qty

Lead/

Ball Finish

(Requires Login)

OPA361AQDCKRQ1

ACTIVE

SC70

DCK

3000

Green (RoHS

& no Sb/Br)

CU NIPDAU Level-2-260C-1 YEAR

⁽¹⁾The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

⁽²⁾Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

⁽³⁾MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

OTHER QUALIFIED VERSIONS OF OPA361-Q1 :

Catalog: OPA361

•

NOTE: Qualified Version Definitions:

Catalog - TI's standard catalog product

•

Addendum-Page 1

PACKAGE MATERIALS INFORMATION

www.ti.com

28-Mar-2011

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device

Package Package Pins

Type Drawing

SPQ

Reel

Pin1

Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant

(mm) W1 (mm)

OPA361AQDCKRQ1

SC70

DCK

3000

179.0

8.4

2.2

2.5

1.2

4.0

8.0

Pack Materials-Page 1

PACKAGE MATERIALS INFORMATION

www.ti.com

28-Mar-2011

*All dimensions are nominal

Device

Package Type Package Drawing Pins

SC70 DCK

SPQ

Length (mm) Width (mm) Height (mm)

195.0 200.0 45.0

OPA361AQDCKRQ1

3000

Pack Materials-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products

Applications

Audio

www.ti.com/audio

amplifier.ti.com

dataconverter.ti.com

www.dlp.com

Communications and Telecom www.ti.com/communications

Amplifiers

Data Converters

DLP® Products

DSP

Computers and Peripherals

Consumer Electronics

Energy and Lighting

Industrial

www.ti.com/computers

www.ti.com/consumer-apps

www.ti.com/energy

dsp.ti.com

www.ti.com/industrial

www.ti.com/medical

www.ti.com/security

Clocks and Timers

Interface

www.ti.com/clocks

interface.ti.com

logic.ti.com

Medical

Security

Logic

Space, Avionics and Defense www.ti.com/space-avionics-defense

Power Mgmt

power.ti.com

Transportation and

Automotive

www.ti.com/automotive

Microcontrollers

RFID

microcontroller.ti.com

www.ti-rfid.com

Video and Imaging

Wireless

www.ti.com/video

www.ti.com/wireless-apps

RF/IF and ZigBee® Solutions www.ti.com/lprf

TI E2E Community Home Page

e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

OPA361AQDCKRQ1相关文章

配单直通车

首天国际（深圳）科技有限公司服务专线: 0755-82807802/82807803 在线联系:

QQ：528164397 复制

QQ：1318502189 复制

深圳市芯福林电子有限公司服务专线: 13418564337 在线联系:

QQ：2881495808 复制

QQ：308365177 复制

北京元坤伟业科技有限公司服务专线: 010-62104931621064316210489162104791 在线联系:

QQ：857273081 复制

QQ：1594462451 复制

柒号芯城电子商务（深圳）有限公司服务专线: 0755-83209937 在线联系:

QQ：2881677436 复制

QQ：2881620402 复制

深圳市中利达电子科技有限公司服务专线: 0755-83200645/13686833545 在线联系:

QQ：1902134819 复制

QQ：2881689472 复制

OPA361AQDCKRQ1产品参数

型号:	OPA361AQDCKRQ1
Brand Name：	Texas Instruments
是否无铅：	不含铅
是否Rohs认证：	符合
生命周期：	Active
IHS 制造商：	TEXAS INSTRUMENTS INC
零件包装代码：	SOIC
包装说明：	TSSOP, TSSOP6,.08
针数：	6
Reach Compliance Code：	compliant
ECCN代码：	EAR99
HTS代码：	8542.33.00.01
Factory Lead Time：	6 weeks
风险等级：	0.77
Is Samacsys：	N
商用集成电路类型：	VIDEO AMPLIFIER
JESD-30 代码：	R-PDSO-G6
JESD-609代码：	e4
长度：	2 mm
湿度敏感等级：	2
信道数量：	1
功能数量：	1
端子数量：	6
最高工作温度：	125 °C
最低工作温度：	-40 °C
封装主体材料：	PLASTIC/EPOXY
封装代码：	TSSOP
封装等效代码：	TSSOP6,.08
封装形状：	RECTANGULAR
封装形式：	SMALL OUTLINE, THIN PROFILE, SHRINK PITCH
峰值回流温度（摄氏度）：	260
电源：	3 V
认证状态：	Not Qualified
筛选级别：	AEC-Q100
座面最大高度：	1.1 mm
子类别：	Audio/Video Amplifiers
最大压摆率：	9 mA
最大供电电压 (Vsup)：	3.3 V
最小供电电压 (Vsup)：	2.5 V
表面贴装：	YES
温度等级：	AUTOMOTIVE
端子面层：	Nickel/Palladium/Gold (Ni/Pd/Au)
端子形式：	GULL WING
端子节距：	0.65 mm
端子位置：	DUAL
处于峰值回流温度下的最长时间：	NOT SPECIFIED
宽度：	1.25 mm
Base Number Matches：	1

电子百科

产品导航

产品型号OPA361AQDCKRQ1的概述

产品型号OPA361AQDCKRQ1的Datasheet PDF文件预览

OPA361AQDCKRQ1相关产品

OPA361AQDCKRQ1相关文章

IC37:专业IC行业平台