A bs ol u t e M ax i m u m Ra t i n gs
1
Free air temperature range
Symbol
V
CC
V
I
V
O
I
IO
T
STG
Parameter
DC Supply Voltage
Input Voltage
Output Voltage
I/O Source Sink
Current
5
Storage Temperature
2, 3, 4
R ec o m m en d ed O pe r a t i ng C on d i t i o ns
Parameter
Commercial
0 to +70
±5
Military
–55 to +125
±10
Units
°C
%V
CC
Units
V
V
V
mA
°C
Limits
–0.5 to +7.0
–0.5 to V
CC
+0.5
–0.5 to V
CC
+0.5
±20
–65 to +150
Temperature
Range
1
Power Supply
Tolerance
2
Notes:
1. Stresses beyond those listed under “Absolute Maximum Ratings”
may cause permanent damage to the device. Exposure to
absolute maximum rated conditions for extended periods may
affect device reliability. Devices should not be operated outside
the recommended operating conditions.
2. V
PP
= V
CC
, except during device programming.
3. V
SV
= V
CC
, except during device programming.
4. V
KS
= GND , except during device programming.
5. Device inputs are normally high impedance and draw extremely
low current. However, when input voltage is greater than V
CC
+
0.5V or less than GND – 0.5V, the internal protection diode will be
forward biased and can draw excessive current.
Notes:
1. Ambient temperature (T
A
) is used for commercial and
industrial; case temperature (T
C
) is used for military.
2. All power supplies must be in the recommended operating range.
For more information, refer to the
Power-Up Design Considerations
application note at
http://www.actel.com/appnotes.
El e c t r i c al S p ec i f i c at i o n s
Commercial
Symbol
V
OH1, 2
V
OL1, 2
V
IH
V
IL
I
IN
I
OZ
C
IO
I
CC(S)
Parameter
HIGH Level Output
Test Condition
I
OH
= –4 mA (CMOS)
I
OH
= –6 mA (CMOS)
LOW Level Output
HIGH Level Input
LOW Level Input
Input Leakage
3-state Output Leakage
I/O Capacitance
3, 4
Standby V
CC
Supply Current V
I
= V
CC
or GND, I
O
= 0 mA
ACT 1
ACT 2/3/1200XL/3200DX
I
CC(D)
Dynamic V
CC
Supply Current
3
2
20
20
mA
mA
I
OL
= +6 mA (CMOS)
TTL Inputs
TTL Inputs
V
I
= V
CC
or GND
V
O
= V
CC
or GND
2.0
–0.3
–10
–10
3.84
0.33
V
CC
+ 0.3
0.8
+10
+10
10
2.0
–0.3
–10
–10
0.4
V
CC
+ 0.3
0.8
+10
+10
10
Min.
Max.
Min.
3.7
Military
Max.
Units
V
V
V
V
V
µA
µA
pF
See the
Notes:
1. Actel devices can drive and receive either CMOS or TTL signal levels. No assignment of I/Os as TTL or CMOS is required.
2. Tested one output at a time, V
CC
= min.
3. Not tested; for information only.
4. V
OUT
= 0V, f = 1 MHz
10
ACTEL [ Actel Corporation ]
