Analog Frequency Multiplier
PL560-xx VCXO Family
PACKAGE PIN DESCRIPTION AND ASSIGNMENT
GNDBUF
VDDBUF
QBAR
Q
OSCOFFSEL
GNDOSC
1
2
16
15
L2X
VDDOSC
OESEL
VDDANA
VDDBUF
QBAR
Q
GNDBUF
VDDANA
OESEL
VDDOSC
L2X
13
14
15
16
OSCOFFSEL
GNDOSC
VCON
XIN
XOUT
OE
DNC
GNDANA
1
2
16
15
L2X
VDDOSC
12
11
10
9
8
7
6
5
GNDBUF
VDDBUF
QBAR
Q
VDDANA
14
13
12
11
10
9
OESEL
12
13
14
15
16
11
10
9
8
7
6
5
GNDANA
DNC
OE
VDDOSC
L4X
OE
XOUT
PLL560-0X
PLL560-4X
3
4
5
6
7
8
VCON
XIN
XOUT
3
4
5
6
7
8
14
13
12
11
10
9
OESEL
VDDANA
VDDBUF
QBAR
P560-4X
1
2
3
4
P560-0X
1
2
3
4
VDDOSC
L2X
XOUT
OE
L4X
VDDOSC
OSCOFF
SEL
GNDOSC
OSCOFF
SEL
GNDOSC
Q
GNDBUF
2X AFM Package Pin Out
VCON
XIN
4X AFM Package Pin Out
PIN ASSIGNMENTS
Name
OSCOFFSEL
GNDOSC
VCON
XIN
XOUT
OE
DNC
L4X
7
I
Pin#
1
2
3
4
5
6
Type
I
P
I
I
O
I
Product
2X & 4X
2X & 4X
2X & 4X
2X & 4X
2X & 4X
2X & 4X
2X
4X
Description
Set to “0” (GND) to choose to turn off the oscillator when outputs are disabled (OE). Default (no
connect) is OSC always on.
GND connection for oscillator circuitry.
Control Voltage input. Use this pin to change the output frequency by varying the applied Control
Voltage.
Input from crystal oscillator circuitry.
Output from crystal oscillator circuitry.
Output Enable input (see "OE LOGIC SELECTION TABLE").
Do Not Connect.
External inductor connection. The inductor is recommended to be a high Q small
size 0402 or 0603 SMD component, and must be placed between L4X and adjacent
VDDOSC. Place inductor as close to the IC as possible to minimize parasitic effects
and to maintain inductor Q. This inductor is used with 4X AFMs.
GND connection.
VDD connection for oscillator circuitry. VDDOSC should be separately decoupled from other
VDDs whenever possible.
GND connection for output buffer circuitry.
PECL/LVDS or CMOS output.
Complementary PECL/LVDS output or in phase CMOS.
VDD connection for output buffer circuitry. VDDBUF should be separately decoupled from other
VDDs whenever possible.
VDD connection for analog circuitry. VDDANA should be separately decoupled from other VDDs
whenever possible.
Selector input to choose the OE control logic (see “OE SELECTION TABLE”). Internal pull-down.
VDD connection for oscillator circuitry. VDDOSC should be separately decoupled from other
VDDs whenever possible.
External inductor connection. The inductor is recommended to be a high Q small
size 0402 or 0603 SMD component, and must be placed between L2X and adjacent
VDDOSC. Place inductor as close to the IC as possible to minimize parasitic effects
and to maintain inductor Q.
GNDANA
8
VDDOSC
GNDBUF
Q
QBAR
VDDBUF
VDDANA
OESEL
VDDOSC
9
10
11
12
13
14
15
P
O
O
P
P
I
P
P
2X
4X
2X & 4X
2X & 4X
2X & 4X
2X & 4X
2X & 4X
2X & 4X
2X & 4X
L2X
16
I
2X & 4X
47745 Fremont Blvd., Fremont, CA 94538 TEL (510) 492-0990, FAX (510) 492-0991
Rev.:02-09-07 Page 13
VCON
XIN
PLL [ PHASELINK CORPORATION ]
