Internet Data Sheet
HYB25DC512[800/160]C[E/F]
512-Mbit Double-Data-Rate SDRAM
1.2
Description
Read and write accesses to the DDR SDRAM are burst
oriented; accesses start at a selected location and continue
for a programmed number of locations in a programmed
sequence. Accesses begin with the registration of an Active
command, which is then followed by a Read or Write
command. The address bits registered coincident with the
Active command are used to select the bank and row to be
accessed. The address bits registered coincident with the
Read or Write command are used to select the bank and the
starting column location for the burst access.
The DDR SDRAM provides for programmable Read or Write
burst lengths of 2, 4 or 8 locations. An Auto Precharge
function may be enabled to provide a self-timed row
precharge that is initiated at the end of the burst access. As
with standard SDRAMs, the pipelined, multibank architecture
of DDR SDRAMs allows for concurrent operation, thereby
providing high effective bandwidth by hiding row precharge
and activation time.
An auto refresh mode is provided along with a power-saving
power-down mode. All inputs are compatible with the Industry
Standard for SSTL_2. All outputs are SSTL_2, Class II
compatible.
Note: The functionality described and the timing
specifications included in this data sheet are for the
DLL Enabled mode of operation.
The 512-Mbit Double-Data-Rate SDRAM is a high-speed
CMOS, dynamic random-access memory containing
536,870,912 bits. It is internally configured as a quad-bank
DRAM.
The 512-Mbit Double-Data-Rate SDRAM uses a double-
data-rate architecture to achieve high-speed operation. The
double data rate architecture is essentially a 2n prefetch
architecture with an interface designed to transfer two data
words per clock cycle at the I/O pins. A single read or write
access
for
the
512-Mbit Double-Data-Rate SDRAM
effectively consists of a single 2n-bit wide, one clock cycle
data transfer at the internal DRAM core and two
corresponding n-bit wide, one-half-clock-cycle data transfers
at the I/O pins.
A bidirectional data strobe (DQS) is transmitted externally,
along with data, for use in data capture at the receiver. DQS
is a strobe transmitted by the DDR SDRAM during Reads and
by the memory controller during Writes. DQS is edge-aligned
with data for Reads and center-aligned with data for Writes.
The 512-Mbit Double-Data-Rate SDRAM operates from a
differential clock (CK and CK; the crossing of CK going HIGH
and CK going LOW is referred to as the positive edge of CK).
Commands (address and control signals) are registered at
every positive edge of CK. Input data is registered on both
edges of DQS, and output data is referenced to both edges of
DQS, as well as to both edges of CK.
TABLE 2
Ordering Information for RoHS Compliant Products
Part Number
HYB25DC512800CE–5
HYB25DC512800CF-5
HYB25DC512160CF-5
HYB25DC512160CE-5
HYB25DC512800CE-6
HYB25DC512800CF-6
HYB25DC512160CF-6
HYB25DC512160CE-6
×16
PG-TSOPII-66
×8
2.5-3-3
166
2-3-3
133
DDR333
PG-TFBGA-60
×16
PG-TSOPII-66
Org. CAS-RCD-RP
Latencies
×8
3-3-3
Clock CAS-RCD-RP
(MHz) Latencies
200
2.5-3-3
Clock Speed
(MHz)
166
DDR400B
Package
PG-TSOPII-66
PG-TFBGA-60
Note
1)
1) RoHS Compliant Product: Restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment as defined
in the directive 2002/95/EC issued by the European Parliament and of the Council of 27 January 2003. These substances include mercury,
lead, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated biphenyl ethers.
Rev. 1.3, 2006-12
03292006-W2FE-ELDX
4
QIMONDA [ QIMONDA AG ]
