Data
Sheet
(Advan ce
Infor m a tio n)
Table 12.3
S29GL-P Memory Array Command Definitions, x8
Cycles
Bus Cycles (Notes
First
Addr
RA
XXX
AAA
AAA
AAA
AAA
AA
AAA
AAA
SA
AAA
AAA
XXX
XXX
XXX
XXX
AAA
AAA
XXX
XXX
AAA
AAA
Data
RD
F0
AA
AA
AA
AA
98
AA
AA
29
AA
AA
A0
80
80
90
AA
AA
B0
30
AA
AA
555
555
55
55
AAA
AAA
88
90
XX
00
555
555
PA
SA
XXX
XXX
555
555
55
55
PD
30
10
00
55
55
AAA
AAA
80
80
AAA
AAA
AA
AA
555
555
55
55
AAA
SA
10
30
555
AAA
F0
20
555
555
55
55
AAA
SA
A0
25
PA
SA
PD
WC
WBL
PD
WBL
PD
555
555
555
555
55
55
55
55
AAA
AAA
AAA
AAA
90
90
90
90
X00
X02
[SA]X04
X06
01
XX7E
X1C
X1E
Second
Addr
Data
Third
Addr
Data
Fourth
Addr
Data
Fifth
Addr
Data
Sixth
Addr
Data
Command (Notes)
Read
Reset
Autoselect (8,9)
Manufacturer ID
Device ID
Sector Protect Verify
Secure Device Verify
1
1
4
4
4
4
1
4
3
1
3
3
2
2
2
2
6
6
1
1
3
4
CFI Query
Program
Write to Buffer
Program Buffer to Flash (confirm)
Write-to-Buffer-Abort Reset
Unlock Bypass
Enter
Program
Sector Erase
Chip Erase
Reset
Chip Erase
Sector Erase
Erase Suspend/Program Suspend
Erase Resume/Program Resume
Secured Silicon Sector Entry
Secured Silicon Sector Exit
Legend
X = Don’t care
RA = Address of the memory to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE# or CE# pulse, whichever happens later.
PD = Data to be programmed at location PA. Data latches on the rising edge of the WE# or CE# pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits A
max
–A16 uniquely select any sector.
WBL = Write Buffer Location. The address must be within the same write buffer page as PA.
WC = Word Count is the number of write buffer locations to load minus 1.
Notes
1. See
for description of bus operations.
2. All values are in hexadecimal.
3. All bus cycles are write cycles unless otherwise noted.
4. Data bits DQ15-DQ8 are don’t cares for unlock and command cycles.
5. Address bits A
MAX
:A16 are don’t cares for unlock and command cycles, unless SA or PA required. (A
MAX
is the Highest Address pin.).
6. No unlock or command cycles required when reading array data.
7. The Reset command is required to return to reading array data when device is in the autoselect mode, or if DQ5 goes high (while the device is providing status
data).
8. See
for device ID values and definitions.
9. The fourth, fifth, and sixth cycles of the autoselect command sequence are read cycles.
10. The data is 00h for an unprotected sector and 01h for a protected sector. See “Autoselect Command Sequence” for more information. This is same as PPB
Status Read except that the protect and unprotect statuses are inverted here.
11. The data value for DQ7 is “1” for a serialized, protected Secured Silicon Sector region and “0” for an unserialized, unprotected region. See
for data and definitions.
12. Command is valid when device is ready to read array data or when device is in autoselect mode.
13. Command sequence returns device to reading array after being placed in a Write-to-Buffer-Abort state. Full command sequence is required if resetting out of
abort while in Unlock Bypass mode.
14. The Unlock-Bypass command is required prior to the Unlock-Bypass-Program command.
15. The Unlock-Bypass-Reset command is required to return to reading array data when the device is in the unlock bypass mode.
16. The system can read and program/program suspend in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase
Suspend command is valid only during a sector erase operation.
17. The Erase Resume/Program Resume command is valid only during the Erase Suspend/Program Suspend modes.
18. The Exit command returns the device to reading the array.
64
S29GL-P MirrorBit
TM
Flash Family
S29GL-P_00_A3 November 21, 2006
SPANSION [ SPANSION ]
