CY28317-2
Byte 11: Recovery Frequency N-Value Register
Bit
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Name
ROCV_FREQ_N7
ROCV_FREQ_N6
ROCV_FREQ_N5
ROCV_FREQ_N4
ROCV_FREQ_N3
ROCV_FREQ_N2
ROCV_FREQ_N1
ROCV_FREQ_N0
Default
0
0
0
0
0
0
0
0
Pin Description
If ROCV_FREQ_SEL is set, CY28317-2 will use the values programmed in
ROCV_FREQ_N[7:0] and ROCV_FREQ_M[6:0] to determine the recovery
CPU output frequency when a Watchdog Timer time-out occurs.
The setting of the FS_Override bit determines the frequency ratio for CPU and
PCI. When it is cleared, CY28317-2 will use the same frequency ratio stated
in the Latched FS[4:0] register. When it is set, CY28317-2 will use the
frequency ratio stated in the SEL[4:0] register.
CY28317-2 supports programmable CPU frequencies ranging from 50 MHz to
248 MHz.
CY28317-2 will change the output frequency whenever there is an update to
either ROCV_FREQ_N[7:0] or ROCV_FREQ_M[6:0]. Therefore, it is recom-
mended to use word or block Write to update both registers within the same
SMBus bus operation.
Byte 12: Recovery Frequency M-Value Register
Bit
Bit 7
Name
ROCV_FREQ_SEL
Default
0
Pin Description
ROCV_FREQ_SEL determines the source of the recover frequency when a
Watchdog Timer time-out occurs. The clock generator will automatically switch
to the recovery CPU frequency based on the selection on ROCV_FREQ_SEL.
0 = From latched FS[4:0]
1 = From the settings of ROCV_FREQ_N[7:0] and ROCV_FREQ_M[6:0]
If ROCV_FREQ_SEL is set, CY28317-2 will use the values programmed in
ROCV_FREQ_N[7:0] and ROCV_FREQ_M[6:0] to determine the recovery
CPU output frequency when a Watchdog Timer time-out occurs.
The setting of the FS_Override bit determines the frequency ratio for CPU,
SDRAM, and PCI. When it is cleared, CY28317-2 will use the same frequency
ratio stated in the Latched FS[4:0] register. When it is set, CY28317-2 will use
the frequency ratio stated in the SEL[4:0] register.
CY28317-2 supports programmable CPU frequencies ranging from 50 MHz to
248 MHz.
CY28317-2 will change the output frequency whenever there is an update to
either ROCV_FREQ_N[7:0] or ROCV_FREQ_M[6:0]. Therefore, it is recom-
mended to use word or block Write to update both registers within the same
SMBus bus operation.
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ROCV_FREQ_M6
ROCV_FREQ_M5
ROCV_FREQ_M4
ROCV_FREQ_M3
ROCV_FREQ_M2
ROCV_FREQ_M1
ROCV_FREQ_M0
0
0
0
0
0
0
0
Byte 13: Programmable Frequency Select N-Value Register
Bit
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Name
CPU_FSEL_N7
CPU_FSEL_N6
CPU_FSEL_N5
CPU_FSEL_N4
CPU_FSEL_N3
CPU_FSEL_N2
CPU_FSEL_N1
CPU_FSEL_N0
Default
0
0
0
0
0
0
0
0
Pin Description
If Prog_Freq_EN is set, CY28317-2 will use the values programmed in
CPU_FSEL_N[7:0] and CPU_FSEL_M[6:0] to determine the CPU output
frequency. The new frequency will start to load whenever CPU_FSELM[6:0]
is updated.
The setting of the FS_Override bit determines the frequency ratio for CPU,
SDRAM and PCI. When it is cleared, CY28317-2 will use the same frequency
ratio stated in the Latched FS[4:0] register. When it is set, CY28317-2 will use
the frequency ratio stated in the SEL[4:0] register.
CY28317-2 supports programmable CPU frequencies ranging from 50 MHz
to 248 MHz.
Rev 1.0, November 25, 2006
Page 10 of 20
SPECTRALINEAR [ SPECTRALINEAR INC ]
