ZL49010/11, ZL49020/21, ZL49030/31
Functional Description
Data Sheet
The ZL490xxs are high performance and low power consumption DTMF receivers. These devices provide wide
dynamic range DTMF detection and a serial decoded data output. These devices also incorporate an energy
detection circuit. An input voiceband signal is applied to the devices via a series decoupling capacitor. Following the
unity gain buffering, the signal enters the AGC circuit followed by an anti-aliasing filter. The bandlimited output is
routed to a dial tone filter stage and to the input of the energy detection circuit. A bandsplit filter is then used to
separate the input DTMF signal into high and low group tones. The high group and low group tones are then
verified and decoded by the internal frequency counting and DTMF detection circuitry. Following the detection
stage, the valid DTMF digit is translated to a 4-bit binary code (via an internal look-up ROM). Data bits can then be
shifted out serially by applying external clock pulses.
Automatic Gain Control (AGC) Circuit
As the device operates on a single power supply, the input signal is biased internally at approximately VDD/2. With
large input signal amplitude (between 0 and approximately -30 dBm for each tone of the composite signal), the
AGC is activated to prevent the input signal from being clipped. At low input level, the AGC remains inactive and the
input signal is passed directly to the hardware DTMF detection algorithm and to the energy detection circuit.
Filter and Decoder Section
The signal entering the DTMF detection circuitry is filtered by a notch filter at 350 and 440 Hz for dial tone rejection.
The composite dual-tone signal is further split into its individual high and low frequency components by two 6
th
order switched capacitor bandpass filters. The high group and low group tones are then smoothed by separate
output filters and squared by high gain limiting comparators. The resulting squarewave signals are applied to a
digital detection circuit where an averaging algorithm is employed to determine the valid DTMF signal. For
ZL490x0, upon recognition of a valid frequency from each tone group, the early steering (ESt) output will go high,
indicating that a DTMF tone has been detected. Any subsequent loss of DTMF signal condition will cause the ESt
pin to go low. For ZL490x1, an internal delayed steering counter validates the early steering signal after a
predetermined guard time which requires no external components. The delayed steering (DStD) will go high only
when the validation period has elapsed. Once the DStD output is high, the subsequent loss of early steering signal
due to DTMF signal dropout will activate the internal counter for a validation of tone absent guard time. The DStD
output will go low only after this validation period.
Energy Detection
The output signal from the AGC circuit is also applied to the energy detection circuit. The detection circuit consists
of a threshold comparator and an active integrator. When the signal level is above the threshold of the internal
comparator (-35 dBm), the energy detector produces an energy present indication on the SD output. The integrator
ensure the SD output will remain at high even though the input signal is changing. When the input signal is
removed, the SD output will go low following the integrator decay time. Short decay time enables the signal
envelope (or cadence) to be generated at the SD output. An external microcontroller can monitor this output for
specific call progress signals. Since presence of speech and DTMF signals (above the threshold limit) can cause
the SD output to toggle, both ESt (DStD) and SD outputs should be monitored to ensure correct signal identification.
As the energy detector is multiplexed with the digital serial data output at the SD pin, the detector output is selected
at all times except during the time between the rising edge of the first pulse and the falling edge of the fourth pulse
applied at the ACK pin.
Serial Data (SD) Output
When a valid DTMF signal burst is present, ESt or DStD will go high. The application of four clock pulses on the
ACK pin will provide a 4-bit serial binary code representing the decoded DTMF digit on the SD pin output. The rising
edge of the first pulse applied on the ACK pin latches and shifts the least significant bit of the decoded digit on the
SD pin. The next three pulses on ACK pin will shift the remaining latched bits in a serial format (see Figure 5). If less
than four pulses are applied to the ACK pin, new data cannot be latched even though ESt/DStD can be valid. Clock
pulses should be applied to clock out any remaining data bits to resume normal operation. Any transitions in excess
4
Zarlink Semiconductor Inc.
ZARLINK [ ZARLINK SEMICONDUCTOR INC ]
