06035C821KAT2A全新原装原理图各脚功能电路原理芯片引脚定义-中国IC网-芯三七

产品型号06035C821KAT2A的Datasheet PDF文件预览

X7R Dielectric

General Speciﬁcations

X7R formulations are called “temperature stable” ceramics and fall into EIA Class II materials. X7R is the most popular

of these intermediate dielectric constant materials. Its temperature variation of capacitance is within ±15% from -55°C to

+125°C. This capacitance change is non-linear.

Capacitance for X7R varies under the inﬂuence of electrical operating con-ditions such as voltage and frequency.

X7R dielectric chip usage covers the broad spectrum of industrial applications where known changes in capacitance due

to applied voltages are acceptable.

PART NUMBER (SEE PAGE 4 FOR COMPLETE PART NUMBER EXPLANATION)

0805

103

Size

(L” x W”)

Voltage

4V = 4

Dielectric

X7R = C

Capacitance

Code (In pF)

2 Sig. Digits +

Number of Zeros

Capacitance

Tolerance

J = ± 5%*

Failure

Rate

A = Not

Applicable

Terminations

Packaging

2 = 7” Reel

4 = 13” Reel

Special

Code

A = Std.

Product

T = Plated Ni and Sn

Z= FLEXITERM^®

6.3V = 6

10V = Z

16V = Y

25V = 3

50V = 5

100V = 1

200V = 2

500V = 7

K = ±10%

*Optional termination

**See FLEXITERM^®

X7R section

Contact

Factory For

Multiples

M = ± 20%

*≤1μF only,

contact factory for

additional values

NOTE: Contact factory for availability of Termination and Tolerance Options for Speciﬁc Part Numbers.

Contact factory for non-speciﬁed capacitance values.

The Important Information/Disclaimer is incorporated in the catalog where these speciﬁcations came from or

available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.

100819

X7R Dielectric

Speciﬁcations and Test Methods

Parameter/Test

Operating Temperature Range

Capacitance

X7R Speciﬁcation Limits

Measuring Conditions

Temperature Cycle Chamber

-55ºC to +125ºC

Within speciﬁed tolerance

Freq.: 1.0 kHz ± 10%

Voltage: 1.0Vrms ± .2V

For Cap > 10µF, 0.5Vrm @ 120Hz

≤ 10% for ≥ 50V DC rating≤ 12.5% for 25V DC rating

≤ 12.5% for 25V and 16V DC rating

≤ 12.5% for ≤ 10V DC rating

Dissipation Factor

Contact Factory for DF by PN

100,000MΩ or 1000MΩ - µF,

whichever is less

Charge device with rated voltage for

120 ± 5 secs @ room temp/humidity

Insulation Resistance

Charge device with 250% of rated voltage for 1-5 seconds, w/

charge and discharge current limited to 50 mA (max)

Note: Charge device with 150% of rated voltage for 500V devices.

Dielectric Strength

No breakdown or visual defects

Appearance

Capacitance

Variation

No defects

≤ ±12%

Resistance to

Flexure

Stresses

Deﬂection: 2mm

Test Time: 30 seconds

Dissipation

Meets Initial Values (As Above)

≥ Initial Value x 0.3

Factor

Insulation

Resistance

≥ 95% of each terminal should be covered with

fresh solder

Dip device in eutectic solder at 230 ± 5ºC

for 5.0 ± 0.5 seconds

Solderability

Appearance

Capacitance

Variation

No defects, <25% leaching of either end terminal

≤ ±7.5%

Dissipation

Dip device in eutectic solder at 260ºC for 60 seconds. Store at

room temperature for 24 ± 2hours before measuring electrical

properties.

Meets Initial Values (As Above)

Resistance to

Solder Heat

Factor

Insulation

Resistance

Dielectric

Strength

Appearance

Capacitance

Variation

No visual defects

≤ ±7.5%

Step 1: -55ºC ± 2º

30 ± 3 minutes

≤ 3 minutes

Step 2: Room Temp

Dissipation

Factor

Insulation

Resistance

Meets Initial Values (As Above)

Step 3: +125ºC ± 2º

30 ± 3 minutes

Thermal Shock

Step 4: Room Temp

≤ 3 minutes

Dielectric

Repeat for 5 cycles and measure after 24 ± 2 hours at room

temperature

Pre-treatment: After mounting, perform heat treatment 150+0/-

10C for 2 hour, then stabilise for 24+/-2 hour at room temp,

then measure.

Meets Initial Values (As Above)

No visual defects

Strength

Appearance

Capacitance

Variation

≤ ±12.5%

Dissipation

Factor

Insulation

Resistance

≤ Initial Value x 2.0 (See Above)

≥ Initial Value x 0.3 (See Above)

Charge device with ≥ rated voltage in test chamber set at

125ºC ± 2ºC for 1000 hours (+48, -0).

Load Life

Pre-treatment: After remove from test chamber, perform heat

treatment 150+0/-10C for 2 hour, then stabilise for 24+/-2 hour

at room temp, then measure.

Dielectric

Strength

Meets Initial Values (As Above)

Contact AVX for datasheet of speciﬁc parts.

Appearance

Capacitance

Variation

No visual defects

≤ ±12.5%

Pre-treatment: After mounting, perform heat treatment 150+0/-

10C for 2 hour, then stabilise for 24+/-2 hour at room temp,

then measure.

Dissipation

Factor

Insulation

Resistance

Dielectric

Strength

≤ Initial Value x 2.0 (See Above)

≥ Initial Value x 0.3 (See Above)

Load

Humidity

Store in a test chamber set at 85ºC ± 2ºC/ 85% ± 5% relative

humidity for 1000 hours (+48, -0) with rated voltage applied.

Pre-treatment: After remove from test chamber, perform heat

treatment 150+0/-10C for 2 hour, then stabilise for 24+/-2 hour

at room temp, then measure.

Meets Initial Values (As Above)

The Important Information/Disclaimer is incorporated in the catalog where these speciﬁcations came from or

available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.

073021

X7R Dielectric

Capacitance Range

PREFERRED SIZES ARE SHADED

SIZE

Soldering

0101*

Reﬂow Only

0201

Reﬂow Only

0402

Reﬂow/Wave

0603

Reﬂow/Wave

0805

Reﬂow/Wave

1206

Reﬂow/Wave

Paper/

Embossed

Packaging

All Paper

Paper/Embossed

0.40 ± 0.02

0.60 ± 0.09

(0.024 ± 0.004)

1.00 ± 0.10

(0.040 ± 0.004)

1.60 ± 0.15

(0.063 ± 0.006)

2.01 ± 0.20

(0.079 ± 0.008)

3.20 ± 0.30

(0.126 ± 0.012)

(L) Length

(in.) (0.016 ± 0.0008)

0.20 ± 0.02

0.30 ± 0.09

(0.011 ± 0.004)

0.50 ± 0.10

(0.020 ± 0.004)

0.81 ± 0.15

(0.032 ± 0.006)

1.25 ± 0.20

(0.049 ± 0.008)

1.60 ± 0.30

(0.063 ± 0.012)

W) Width

(in.) (0.008 ± 0.0008)

0.10± 0.04

0.15 ± 0.05

0.25 ± 0.15

0.35 ± 0.15

0.50 ± 0.25

(t) Terminal

WVDC

Cap

(pF)

(in.) (0.004 ± 0.0016)

(0.006 ± 0.002)

(0.010 ± 0.006)

(0.014 ± 0.006)

(0.020 ± 0.010)

6.3 10 16 25 50 6.3 10 16 25 50 100 6.3 10 16 25 50 100 200 250 6.3 10 16 25 50 100 200 250 6.3 10 16 25 50 100 200 250 500

100 101

150 151

220 221

330 331

470 471

680 681

1000 102

1500 152

2200 222

3300 332

3900 392

4700 472

5600 562

6800 682

0.01 103

Cap

(μF) 0.012 123

0.015 153

0.018 183

0.022 223

0.027 273

0.033 333

0.039 393

0.047 473

0.068 683

0.082 823

0.1 104

0.12 124

0.15 154

0.22 224

0.33 334

0.47 474

0.68 684

1.0 105

2.2 225

4.7 475

10 106

22 226

47 476

100 107

WVDC

6.3 10 16 25 50 6.3 10 16 25 50 100 6.3 10 16 25 50 100 200 250 6.3 10 16 25 50 100 200 250 6.3 10 16 25 50 100 200 250 500

SIZE

0101*

0201

0402

0603

0805

1206

Letter

Max.

Thickness

0.33

(0.013)

0.22

(0.009)

0.56

(0.022)

0.71

(0.028)

0.90

(0.035)

0.94

(0.037)

1.02

(0.040)

1.27

(0.050)

1.40

(0.055)

1.52

(0.060)

1.78

(0.070)

2.29

(0.090)

2.54

(0.100)

2.79

(0.110)

PAPER

EMBOSSED

NOTE: Contact factory for non-speciﬁed capacitance values

*EIA 01005

**Contact Factory for Speciﬁcations

The Important Information/Disclaimer is incorporated in the catalog where these speciﬁcations came from or

available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.

071621

X7R Dielectric

Capacitance Range

PREFERRED SIZES ARE SHADED

SIZE

Soldering

1210

Reﬂow Only

1812

Reﬂow Only

1825

Reﬂow Only

2220

Reﬂow Only

2225

Reﬂow Only

Packaging

Paper/Embossed

All Embossed

(in.)

3.30 ± 0.4

(0.130± 0.016)

4.50 ± 0.40

(0.177 ± 0.016)

4.50 ± 0.40

(0.177 ± 0.016)

5.70 ± 0.50

(0.224 ± 0.020)

5.70 ± 0.40

(0.224 ± 0.016)

(L) Length

(in.)

2.50 ± 0.30

(0.098 ± 0.012)

3.20 ± 0.40

(0.126 ± 0.016)

6.40 ± 0.40

(0.252 ± 0.016)

5.00 ± 0.40

(0.197 ± 0.016)

6.30 ± 0.40

(0.248 ± 0.016)

W) Width

(in.)

0.50 ± 0.25

(0.020 ± 0.010)

0.61 ± 0.36

(0.024 ± 0.014)

0.61 ± 0.36

(0.024 ± 0.014)

0.64 ± 0.39

(0.025 ± 0.015)

0.64 ± 0.39

(0.025 ± 0.015)

(t) Terminal

WVDC

100 101

150 151

220 221

330 331

470 471

680 681

1000 102

1500 152

2200 222

3300 332

4700 472

6800 682

0.01 103

0.015 153

0.022 223

0.033 333

0.047 473

0.068 683

0.1 104

0.15 154

0.22 224

0.33 334

0.47 474

0.68 684

1.0 105

1.5 155

2.2 225

3.3 335

4.7 475

100

200

500

100

200

500

100

200

100

200

500

100 200

Cap

(pF)

Cap

(μF)

10 106

22 226

47 476

100 107

WVDC

SIZE

1210

100

200

500

100

1812

200

500

100

1825

200

100

2220

200

500

100

2225

200

Letter

Max.

Thickness

0.33

(0.013)

0.22

(0.009)

0.56

(0.022)

0.71

(0.028)

0.90

(0.035)

0.94

(0.037)

1.02

(0.040)

1.27

(0.050)

1.40

(0.055)

1.52

(0.060)

1.78

(0.070)

2.29

(0.090)

2.54

(0.100)

2.79

(0.110)

3.30

(0.130)

PAPER

EMBOSSED

NOTE: Contact factory for non-speciﬁed capacitance values

The Important Information/Disclaimer is incorporated in the catalog where these speciﬁcations came from or

available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.

080221

型号:	06035D104KAT2A
是否无铅：	不含铅
是否Rohs认证：	符合
生命周期：	Active
零件包装代码：	0603
包装说明：	CHIP
Reach Compliance Code：	compliant
ECCN代码：	EAR99
HTS代码：	8532.24.00.20
风险等级：	1.38
电容：	0.1 µF
电容器类型：	CERAMIC CAPACITOR
介电材料：	CERAMIC
高度：	0.9 mm
JESD-609代码：	e3
长度：	1.6 mm
安装特点：	SURFACE MOUNT
多层：	Yes
负容差：	10%
端子数量：	2
最高工作温度：	85 °C
最低工作温度：	-55 °C
封装形式：	SMT
包装方法：	TR, Paper, 7 Inch
极性：	NON-POLARIZED
正容差：	10%
额定（直流）电压（URdc）：	50 V
尺寸代码：	0603
表面贴装：	YES
温度特性代码：	X5R
温度系数：	15% ppm/ °C
端子面层：	Matte Tin (Sn) - with Nickel (Ni) barrier
端子形状：	WRAPAROUND
宽度：	0.81 mm
Base Number Matches：	1

电子百科

产品导航

产品型号06035C821KAT2A的概述

产品型号06035C821KAT2A的Datasheet PDF文件预览

06035C821KAT2A相关产品

06035C821KAT2A相关文章

IC37:专业IC行业平台