X9241A
Absolute Maximum Ratings
Temperature under bias . . . . . . . . . . . . . . . . . . . . . . . .-65 to +135°C
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . .-65 to +150°C
Voltage on SCK, SCL or any address
input with respect to V
SS
. . . . . . . . . . . . . . . . . . . . . . . -1V to +7V
Voltage on any V
H
/R
H
, V
W
/R
W
or V
L
/R
L
referenced to V
SS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +6V/-4V
∆V
= |V
H
/R
H
- V
L
/R
L
| . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10V
Lead temperature (soldering, 10 seconds) . . . . . . . . . . . . . . . 300°C
I
W
(10 seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
Recommended Operating Conditions
Temperature (Commercial) . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
Temperature (Industrial). . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Supply Voltage (V
CC
) Limits
X9241A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V ± 10%
CAUTION: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; the functional
operation of the device (at these or any other conditions above those listed in the operational sections of this specification) is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
Analog Specifications
SYMBOL
R
TOTAL
(Over recommended operating conditions unless otherwise stated.)
LIMITS
PARAMETER
TEST CONDITION
MIN
-20
25°C, each pot
See Note 7, 8
Wiper Current = ± 1mA (Note 7)
-3.0
Ref: 1kHz See Note 5
See Note 5
R
w(n)(actual)
- R
w(n)(expected)
R
w(n + 1)
- [R
w(n) + MI
]
See Note 5
See Note 5
See Circuit #3 and Note 5
V
IN
= V
TERM
. Device is in stand-by
mode.
15/15/25
0.1
1
±300
±20
≤120
1.6
0.4
±1
±0.2
40
130
+5
TYP
MAX
+20
50
UNIT
%
mW
mA
Ω
V
dBV
%
MI
(3)
MI
(3)
ppm/°C
ppm/C
pF
µA
End to end resistance
Power rating
I
W
R
W
V
TERM
Wiper current
Wiper resistance
Voltage on any V
H
/R
H
, V
W
/R
W
or V
L
/R
L
Pin
Noise
Resolution
(4)
Absolute linearity
(1)
Relative linearity
(2)
Temperature Coefficient of R
TOTAL
Ratiometric temperature coefficient
C
H
/C
L
/C
W
l
AL
Potentiometer capacitances
R
H
, R
I
, R
W
leakage current
DC Electrical Specifications
SYMBOL
l
CC
I
SB
I
LI
I
LO
V
IH
V
IL
V
OL
PARAMETER
Supply current (active)
V
CC
current (standby)
Input leakage current
Output leakage current
Input HIGH voltage
Input LOW voltage
Output LOW voltage
(Over recommended operating conditions unless otherwise stated.)
LIMITS
TEST CONDITION
f
SCL
= 100kHz, SDA = Open, Other
Inputs = V
SS
SCL = SDA = V
CC
, Addr. = V
SS
V
IN
= V
SS
to V
CC
V
OUT
= V
SS
to V
CC
2
-1
I
OL
= 3mA
200
MIN
TYP
MAX
3
500
10
10
V
CC
+ 1
0.8
0.4
UNIT
mA
µA
µA
µA
V
V
V
Notes:
(1) Absolute Linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as
a potentiometer.
(2) Relative Linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potenti-
ometer. It is a measure of the error in step size.
(3) MI = RTOT/63 or (R
H
–R
L
)/63, single pot
(4) Max. = all four arrays cascaded together, Typical = individual array resolutions.
10
FN8164.1
September 15, 2005
INTERSIL [ INTERSIL CORPORATION ]
