E3X-DA-N
Ratings and Specifications
Amplifiers
Pre-wired Amplifiers
Type
Output
type
Item
Light source
(wavelength)
Power supply voltage
Power consumption
NPN
output
PNP
output
Standard
models
E3X
-DA11-N
E3X
-DA41-N
Red LED (660 nm)
Monitor-
output
models
E3X
-DA21-N
E3X
-DA51-N
Mark-detecting models
E3X
-DAB11-N
E3X
-DAB41-N
Blue LED
(470 nm)
E3X
-DAG11-N
E3X
-DAG41-N
Green LED
(525 nm)
Infrared
models
E3X
-DAH11-N
E3X
-DAH41-N
Infrared LED
(870 nm)
Water-
resistant
models
E3X
-DA11V
E3X
-DA41V
Red LED (660 nm)
Twin-output
models
E3X
-DA11TW
E3X
-DA41TW
For dimensions, refer to page 26 to 29.
12 to 24 VDC±10%, ripple (p-p) 10% max.
Normally: 960 mW max. (current consumption: 40 mA max. at power supply voltage of 24 VDC)
Eco Mode: 720 mW max. (current consumption: 30 mA max. at power supply voltage of 24 VDC)
Digital display not lit: 600 mW max. (current consumption: 25 mA max. at power supply voltage of 24 VDC)
Load current: 50 mA (residual voltage (NPN/PNP): 1 V max.,
Open collector (NPN or PNP output, depending on the model)
Light ON/Dark ON selectable
---
Load 1 to
5 VDC,
10 kΩ min.
---
Con-
trol
output
ON/OFF
output
Monitor
output
Protection circuit
Power supply reverse polarity, Output short-circuit protection, Mutual interference prevention (supported for up to 10
Units)
0.5 ms for
operation and
reset
respectively
2 ms for
operation and
reset
7 ms for
operation and
reset
respectively
Super-high-
speed mode
Re-
Standard
sponse
mode
time
Super-long-
distance
mode
Sensitivity setting
Timer func-
tion
Automatic
power con-
trol (APC)
Func-
tions
Zero-reset
Initial reset
0.25 ms for operation and reset respectively
1 ms for operation and reset respectively
4 ms for operation and reset respectively
Teaching or manual method
OFF-delay timer: 0 to 200 ms, 1 to 20 ms (set in 1-ms units); 20 to 200 ms (set in 5-ms units)
Using Mobile Console: OFF delay, ON delay, or one shot (selectable)
Fiber-optic current digital
control
Negative values can be displayed.
Settings can be returned to defaults as required.
Upper and
lower limits
can be set as
required for
every 100
digital values.
---
Fiber-optic current digital control
Monitor fo-
cus
---
---
Indicators
Display timing
Display orientation
Optical axis adjust-
ment
Ambient illumination
(receiver side)
Operation indicator (orange), 7-segment digital incident level display (red), 7-segment digital incident level percentage
display (red), threshold and excess gain 2-color double bar indicators (green and red), 7-segment digital threshold
display (red)
Switching between normal/peak-hold/bottom-hold possible
Switching between normal/reverse possible
Optical axis adjustment possible (hyper-flashing function)
Incandescent lamp: 10,000 lx max.
Sunlight: 20,000 lx max.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 All Rights Reserved.
6
OMRON [ OMRON ELECTRONICS LLC ]
