BU17102AKV-ME中文资料应用文章市场行情现货热卖使用介绍-中国IC网-芯三七

Datasheet

Clockless Link Interface LSI

24bit Clockless Link

Receiver

BU17102AKV-M

●General Description

●Key Specifications

BU17101AKV-M is a differential serial interface IC that

expect further low power consumption and low EMI by

ROHM's original CDR(Clock Data Recovery) technology.

The BU17102AKV-M receiver deserializes 24-bit

CMOS level signals, and transfer by the differential lines

of 1 pair. There is no return path. Reset line and link

synchronous control line are unnecessary. The

BU17102AKV-M links automatically.

¢ I/O voltage range:

¢ 3.3V voltage range:

¢ Clock frequency range:

¢ Transmission data rate:

¢ Effective throughput:

¢ Operating temperature range:

2.3 to 3.6 V

30M to 51M Hz

0.960G to 1.630 Gbps

0.720G to 1.224 Gbps

-40 to +85 ℃

●Package

W(Typ.) x D(Typ.) x H(Max.)

9.00mm x 9.00mm x 1.63mm

VQFP48

●Features

■ High-speed differential serial interface (Maximum

1.6Gbps)

■ Embedded clock interface

■ No lock condition signal and no reset signal between

transmitter and receiver. (Only differential signals)

■ Low EMI transmission by original DC balance protocol

and scrambling.

■ Selectable 2 modes of CMOS parallel output current.

●Applications

■ Car navigation display interface

■ Printer display interface

○Product structure：Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays

www.rohm.co.jp

TSZ02201-0L2L0HZ00200-1-2

16.Jan.2013 Rev.001

1/6

TSZ22111・14・001

Datasheet

BU17102AKV-M

●Block Diagram

BU17102AKV-M (Rx)

VDD33

VDDIO

DFRX+(-)

DFRX-(+)

PD[23:0]

PCLK

CDR

Timing Gen

PCLK

ERR

RVDD

REG

POL

F_XS

OE

PLLBW[1:0]

TESTPT

Operation Control

TEST[1:0]

GND

Figure 1. Block Diagram

www.rohm.co.jp

TSZ02201-0L2L0HZ00200-1-2

16.Jan.2013 Rev.001

2/6

TSZ22111・15・001

Datasheet

BU17102AKV-M

●Typical Application Circuit

+

-

(47uF)

0.1uF x 2

3.3V

-

0.47uF

0.01uF

0.47uF

0.01uF

0.1uF x 2

1uF

0.1uF x 3

0.1uF

PD[23:0]

DFTX+

DFTX-

DFRX+(-)

PD[23:0]

Stream

ストリーム

Data

データ

ストリーム

データ

Data

Stream

DFRX-(+)

PCLK

ERR

PCLK

ERR

POL

TESTPT

TEST1

TESTPT

TEST1

TEST0

DFSET1

DFSET0

OE

F_XS

TEST0

Reset(Rx)

Reset(Tx)

リセット(Tx)

リセット(Rx)

Figure 2. Typical Application Circuit

www.rohm.co.jp

TSZ02201-0L2L0HZ00200-1-2

16.Jan.2013 Rev.001

3/6

TSZ22111・15・001

Datasheet

BU17102AKV-M

●Ordering Information

B U 1 7 1 0 2 A K V - M

E 2

Part No.

Package

KV: VQFP48

Packaging and forming specification

E2: Embossed tape and reel

●Marking Diagram

VQFP48 (TOP VIEW)

Part Number Marking

LOT Number

BU17102A

1PIN MARK

www.rohm.co.jp

TSZ02201-0L2L0HZ00200-1-2

16.Jan.2013 Rev.001

4/6

TSZ22111・15・001

Datasheet

BU17102AKV-M

●Physical Dimension Tape and Reel Information

Package Name

VQFP48

Tape

Embossed carrier tape

1500pcs

Quantity

E2

Direction

of feed

The direction is the 1pin of product is at the upper left when you hold

reel on the left hand and you pull out the tape on the right hand

(

)

Direction of feed

1pin

Reel

Order quantity needs to be multiple of the minimum quantity.

www.rohm.co.jp

TSZ02201-0L2L0HZ00200-1-2

16.Jan.2013 Rev.001

5/6

TSZ22111・15・001

Datasheet

BU17102AKV-M

●Revision History

Date

Revision

001

Changes

16.Jan.2013

New Release

www.rohm.co.jp

TSZ02201-0L2L0HZ00200-1-2

16.Jan.2013 Rev.001

6/6

TSZ22111・15・001

Daattaasshheeeett

Notice

Precaution on using ROHM Products

(Note 1)

1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment

,

aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,

bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales

representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way

responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any

ROHM’s Products for Specific Applications.

(Note1) Medical Equipment Classification of the Specific Applications

JAPAN

USA

EU

CHINA

CLASSⅢ

CLASSⅣ

CLASSⅡb

CLASSⅢ

2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor

products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate

safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which

a failure or malfunction of our Products may cause. The following are examples of safety measures:

[a] Installation of protection circuits or other protective devices to improve system safety

[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.

Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the

use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our

Products under any special or extraordinary environments or conditions (as exemplified below), your independent

verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents

[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust

[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,

H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves

[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items

[f] Sealing or coating our Products with resin or other coating materials

[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of

flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning

residue after soldering

[h] Use of the Products in places subject to dew condensation

4. The Products are not subject to radiation-proof design.

5. Please verify and confirm characteristics of the final or mounted products in using the Products.

6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,

confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power

exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect

product performance and reliability.

7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual

ambient temperature.

8. Confirm that operation temperature is within the specified range described in the product specification.

9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in

this document.

Precaution for Mounting / Circuit board design

1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product

performance and reliability.

2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must

be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,

please consult with the ROHM representative in advance.

For details, please refer to ROHM Mounting specification

Notice-SS

Rev.004

Daattaasshheeeett

Precautions Regarding Application Examples and External Circuits

1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the

characteristics of the Products and external components, including transient characteristics, as well as static

characteristics.

2. You agree that application notes, reference designs, and associated data and information contained in this document

are presented only as guidance for Products use. Therefore, in case you use such information, you are solely

responsible for it and you must exercise your own independent verification and judgment in the use of such information

contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses

incurred by you or third parties arising from the use of such information.

Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper

caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be

applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,

isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

Precaution for Storage / Transportation

1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2

[b] the temperature or humidity exceeds those recommended by ROHM

[c] the Products are exposed to direct sunshine or condensation

[d] the Products are exposed to high Electrostatic

2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period

may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is

exceeding the recommended storage time period.

3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads

may occur due to excessive stress applied when dropping of a carton.

4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of

which storage time is exceeding the recommended storage time period.

Precaution for Product Label

QR code printed on ROHM Products label is for ROHM’s internal use only.

Precaution for Disposition

When disposing Products please dispose them properly using an authorized industry waste company.

Precaution for Foreign Exchange and Foreign Trade act

Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,

please consult with ROHM representative in case of export.

Precaution Regarding Intellectual Property Rights

1. All information and data including but not limited to application example contained in this document is for reference

only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any

other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable

for infringement of any intellectual property rights or other damages arising from use of such information or data.:

2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any

third parties with respect to the information contained in this document.

Other Precaution

1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.

2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written

consent of ROHM.

3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the

Products or this document for any military purposes, including but not limited to, the development of mass-destruction

weapons.

4. The proper names of companies or products described in this document are trademarks or registered trademarks of

ROHM, its affiliated companies or third parties.

Notice-SS

Rev.004

Daattaasshheeeett

General Precaution

1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.

ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny

ROHM’s Products against warning, caution or note contained in this document.

2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior

notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s

representative.

3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all

information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or

liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or

concerning such information.

Notice – WE

Rev.001

型号:	BU17102AKV-ME2
是否Rohs认证：	符合
生命周期：	Active
包装说明：	LFQFP,
Reach Compliance Code：	compliant
HTS代码：	8542.39.00.01
Factory Lead Time：	16 weeks
风险等级：	1.63
商用集成电路类型：	CONSUMER CIRCUIT
JESD-30 代码：	S-PQFP-G48
长度：	7 mm
功能数量：	1
端子数量：	48
最高工作温度：	85 °C
最低工作温度：	-40 °C
封装主体材料：	PLASTIC/EPOXY
封装代码：	LFQFP
封装形状：	SQUARE
封装形式：	FLATPACK, LOW PROFILE, FINE PITCH
峰值回流温度（摄氏度）：	NOT SPECIFIED
座面最大高度：	1.625 mm
最大供电电压 (Vsup)：	3.6 V
最小供电电压 (Vsup)：	2.3 V
表面贴装：	YES
温度等级：	INDUSTRIAL
端子形式：	GULL WING
端子节距：	0.5 mm
端子位置：	QUAD
处于峰值回流温度下的最长时间：	NOT SPECIFIED
宽度：	7 mm
Base Number Matches：	1

电子百科

产品导航

产品型号BU17102AKV-ME2的Datasheet PDF文件预览

BU17102AKV-ME相关产品..

BU17102AKV-ME相关文章

IC37:专业IC行业平台