MXD1818UR26+全新原装原理图各脚功能电路原理芯片引脚定义-中国IC网-芯三七

MXD1810–MXD1813/

MXD1815–MXD1818

Low-Power μP Reset Circuits in 3-Pin

SC70/SOT23

General Description

Features

The MXD1810–MXD1813/MXD1815–MXD1818 fam-

ily of microprocessor (μP) reset circuits monitor power

supplies in μP and digital systems. These devices

provide excellent circuit reliability and low cost by

eliminating external components and adjustments when

used with +2.5V/+3.0V/+3.3V (MXD1815–MXD1818),

and +5V (MXD1810–MXD1813) systems.

● Precision Monitoring of +2.5V, +3V, +3.3V, and +5V

Power-Supply Voltages

● Available in Four Reset Output Configurations

● Factory-Set Reset Threshold Voltages: 2.18V,

2.31V, 2.55V, 2.88V, 3.06V, 4.12V, 4.37V, 4.62V

● ±2.5% Reset Threshold Accuracy Over Temperature

● Fixed Reset Timeout Period: 100ms (min)

These circuits assert a reset signal whenever the V

CC

supply voltage declines below a preset threshold, keeping

reset asserted for at least 100ms after V rises above the

● Guaranteed RESET/RESET Valid to V

● Debounced Manual-Reset Detect (MXD1813/

MXD1818)

= +1V

CC

reset threshold. The MXD1813/MXD1818 also keep reset

asserted for at least 100ms after the output is momentarily

pulled to GND by an external pushbutton switch.

● Power-Supply Transient Immunity

● No External Components

The MXD1812/MXD1817 have an active-high push-

pull RESET output. The MXD1810/MXD1815 (push-

pull) and MXD1811/MXD1813/MXD1816/MD1818 (open-

drain) have an active-low RESET output. The open-drain

● Low Power Consumption (4μA)

● Pin Compatible with DS181_ Products (SOT23)

● 3-Pin SC70 and SOT23 Packages

devices

(MXD1811/MXD1813/MXD1816/MXD1818)

Ordering Information

have an internal pullup resistor to V . The MXD1813/

CC

†

PART

TEMP RANGE

-40°C to +105°C

PIN-PACKAGE

3 SOT23

MXD1818 feature a debounced manual-reset feature that

asserts a reset if the RESET pin is pulled low for more

than 1.5μs. When used to initiate manual reset, RESET

debounces signals from devices such as mechanical

switches. For devices with this feature, the release of the

external switch triggers the reset period.

MXD1810UR_ _-T

MXD1810XR_ _-T

3 SC70

†The MXD1810–MXD1813/MXD1815–MXD1818 are available

with factory-set V reset thresholds from +2.18V to +3.06V

CC

(MXD1815–MXD1818) and +4.12V to +4.62V (MXD1810–

MXD1813). Choose the desired reset-threshold suffix from the

Reset Threshold Table and insert it in place of the “_ _”

following “R” in the part number. All devices are available in

tape-and-reel only in 2500 unit increments. Other threshold

voltages may be available. Contact factory for availability.

The MXD1810–MXD1813/MXD1815–MXD1818 are

guaranteed to output the correct logic state for V

down

CC

to +1V. These ICs provide a reset comparator designed

to ignore fast transients on V . Reset thresholds are

CC

Devices are available in both leaded and lead(Pb)-free packag-

ing. Specify lead-free by replacing “-T” with “+T” when ordering.

available between +2.18V and +4.62V. These

small, low-power (4μA) devices are ideal for use in

portable equipment. All are available in space-saving

3-pin SC70 and SOT23 packages, and are specified from

-40°C to +105°C.

Ordering Information continued at end of data sheet.

Pin Conﬁgurations

TOP VIEW

Applications

● Computers and Controllers

● Intelligent Instruments

● Set-Top Boxes

● Printers

● Critical μP and μC Monitoring

● Portable/Battery-Powered Equipment

RESET

V

1

2

1

2

CC

(RESET)

GND

3

MXD181_X

SC70-3

3

GND

MXD181_U

SOT23-3

RESET

(RESET)

V

CC

() ARE FOR THE MXD1812/MXD1817

19-2243; Rev 2; 11/14

MXD1810–MXD1813/

MXD1815–MXD1818

Low-Power μP Reset Circuits in 3-Pin

SC70/SOT23

Absolute Maximum Ratings

V

to GND .........................................................-0.3V to +6.0V

Output Current (RESET, RESET)......................................20mA

CC

Push-Pull RESET (MXD1810/MXD1815),

RESET (MXD1812/MXD1817) to GND...-0.3V to (V

Open-Drain RESET (MXD1811/MXD1816)

to GND..............................................................-0.3V to +6.0V

Open-Drain RESET (MXD1813/MXD1818)

to GND.................................................. -0.3V to (V

Continuous Power Dissipation (T = +70°C)

A

+ 0.3V)

3-Pin SC70 (derate 2.17mW above +70°C)................174mW

3-Pin SOT23 (derate 4mW/°C above +70°C) .............320mW

Operating Temperature Range .........................-40°C to +105°C

Junction Temperature......................................................+150°C

Storage Temperature Range .............................-65°C to +150°C

Lead Temperature (soldering, 10s) .................................+300°C

CC

+ 0.3V)

CC

Input Current (V , RESET)..............................................20mA

CC

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these

or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect

device reliability.

Electrical Characteristics

(V

= full range, T = -40°C to +105°C, unless otherwise specified. Typical values are at T = +25°C.) (Note 1)

CC

A

PARAMETER

SYMBOL

CONDITIONS

= 0°C to +105°C

MIN

1.0

TYP

MAX UNITS

T

5.5

V

A

Supply Voltage Range

Supply Current

V

CC

= -40°C to +105°C

1.2

5.5

A

V

= +5.5V, V

= +3.6V, V

> V , no load

9

16

µA

10

CC

TH

I

CC

> V , no load

4

CC

TH

MXD181_ _ R46

MXD181_ _ R44

MXD181_ _ R41

MXD181_ _ R31

MXD181_ _ R29

MXD181_ _ R26

MXD181_ _ R23

MXD181_ _ R22

4.50

4.25

4.00

2.98

2.80

2.47

2.25

2.12

100

4.62

4.37

4.12

3.06

2.88

2.55

2.31

2.18

150

2

4.75

4.49

4.24

3.15

V

Reset Threshold

V

TH

2.97

2.64

2.37

2.25

Active Reset-Timeout Period

t

V

rising

250

5

ms

µs

RP

CC

= (V + 100mV) falling to (V - 200mV)

TH

V

to Reset Delay

t

CC

RD

rising, t = 5μs

100

1.5

150

250

ms

µs

R

Push-Button Detect to Reset

t

MXD1813/MXD1818 only

PB

Push-Button Reset-Timeout Period

t

100

150

250

0.34

0.15

ms

PBRST

T

= +25°C to +105°C

= -40°C to +25°C

MXD1813/MXD1818

only

A

Input Low Voltage

V

IL

T

A

Input High Voltage

V

I

MXD1813/MXD1818 only

0.7 × V

IH

CC

V

≥ V , reset not asserted,

CC

TH(MAX)

RESET Output Source Current

350

μA

OH

MXD1810/MXD1815

V

≥ V , reset asserted,

CC

TH(MAX)

RESET Output Source Current

RESET Output Sink Current

I

μA

mA

MXD1812/MXD1817

V

≥ 2.7V, reset asserted, V

= 0.4V

OUT

CC

I

MXD1810/MXD1811/MXD1813/MXD1815/

MXD1816/MXD1818 (Note 2)

10

OL

V

≥ 2.7V, reset not asserted, V

= 0.4V

CC

OUT

I

MXD1812/MXD1817

Maxim Integrated

│ 2

www.maximintegrated.com

MXD1810–MXD1813/

MXD1815–MXD1818

Low-Power μP Reset Circuits in 3-Pin

SC70/SOT23

Electrical Characteristics (continued)

(V

= full range, T = -40°C to +105°C, unless otherwise specified. Typical values are at T = +25°C.) (Note 1)

CC

A

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

MAX UNITS

V

0.5

-

V

0.1

-

CC

Output High Voltage

V

0 < I

< 500μA

V

OH

Output Capacitance (Note 2)

C

10

7.5

pF

kΩ

OUT

MXD1811/MXD1816

3.5

3.1

5.5

Internal Pullup Resistor,

Open-Drain

R

P

MXD1813/MXD1818

Note 1: Production testing done at T = +25°C; limits over temperature guaranteed by design.

A

Note 2: The MXD1811/MXD1813/MXD1816/MXD1818 have an internal pullup resistor which may deliver 1mA of sink current.

Note 3: Guaranteed by design.

Typical Operating Characteristics

(T = +25°C, unless otherwise noted.)

A

NORMALIZED RESET THRESHOLD

vs. TEMPERATURE (V FALLING)

RESET TIMEOUT PERIOD

SUPPLY CURRENT vs. TEMPERATURE

vs. TEMPERATURE (V RISING)

CC

1.010

1.005

1.000

0.995

0.990

10

RESET/RESET NOT ASSERTED

160

156

152

148

144

140

V

= +5V

CC

8

6

4

2

0

V

= +5V

CC

V

= +4.62V

TH

V

= +2.5V

CC

V

= +2.18V

TH

V

= +3.3V

CC

V

= +2.5V

CC

-40

-10

20

50

80

110

-40

-10

20

50

80

110

-04

-01

20

50

80

110

TEMPERATURE (°C)

OUTPUT VOLTAGE

vs. OUTPUT SINK CURRENT

POWER-DOWN RESET DELAY

vs. TEMPERATURE

MAXIMUM TRANSIENT DURATION

vs. RESET THRESHOLD OVERDRIVE

100

3.0

2.5

2.0

1.5

1.0

0.5

0

200

160

120

80

90

80

70

60

50

40

30

20

10

0

V

= +4.62V

TH

RESET OCCURS

ABOVE THIS LINE

V

= +2.18V

TH

40

0

110

-40

-10

20

50

80

10

100

1000

0

3

6

9

12

15

RESET THRESHOLD OVERDRIVE, V - V (mV)

TEMPERATURE (°C)

OUTPUT CURRENT (mA)

TH CC

Maxim Integrated

│ 3

www.maximintegrated.com

MXD1810–MXD1813/

MXD1815–MXD1818

Low-Power μP Reset Circuits in 3-Pin

SC70/SOT23

Typical Operating Characteristics (continued)

(T = +25°C, unless otherwise noted.)

A

OUTPUT VOLTAGE

vs. OUTPUT SOURCE CURRENT

INPUT LOW VOLTAGE

vs. V AND TEMPERATURE

CC

0.5

0.4

0.3

0.2

0.1

0

0.8

0.6

0.4

0.2

V

= +5.5V

CC

V

= +2.2V

CC

110

-40

-10

20

50

80

3.0

0

0.5

1.0

1.5

2.0

2.5

TEMPERATURE (°C)

OUTPUT CURRENT (mA)

Pin Descriptions

MXD1810/MXD1815

NAME

FUNCTION

Push-Pull, Active-Low Reset Output. RESET changes from high to low when V

SC70

SOT23

drops

CC

2

1

RESET

below the selected reset threshold. RESET remains low for the reset timeout period after

exceeds the device reset threshold.

V

CC

1

3

2

V

Supply Voltage and Input for Reset-Threshold Monitor

Ground

CC

3

GND

MXD1811/MXD1816

NAME

FUNCTION

SC70

SOT23

Open-Drain, Active-Low Reset Output. RESET changes from high to low when V

drops

CC

2

1

RESET

below the selected reset threshold. RESET remains low for the reset timeout period after

exceeds the device reset threshold. RESET has an internal 5.5kΩ pullup resistor.

V

CC

1

3

2

V

Supply Voltage and Input for Reset-Threshold Monitor

Ground

CC

3

GND

Maxim Integrated

│ 4

www.maximintegrated.com

MXD1810–MXD1813/

MXD1815–MXD1818

Low-Power μP Reset Circuits in 3-Pin

SC70/SOT23

Pin Description (continued)

MXD1812/MXD1817

NAME

FUNCTION

SC70

SOT23

Push-Pull, Active-High Reset Output. RESET changes from low to high when V

drops

CC

2

1

RESET

below the selected reset threshold. RESET remains high for the reset timeout period after

V

exceeds the device reset threshold.

CC

1

3

2

V

Supply Voltage and Input for Reset- Threshold Monitor

Ground

CC

3

GND

MXD1813/MXD1818

NAME

FUNCTION

SC70

SOT23

Open-Drain, Active-Low Reset Output with Manual Reset Detect. RESET changes from

high to low when V

drops below the selected reset threshold, or RESET is externally

CC

2

1

RESET

pulled low for at least 1.5μs. RESET remains low for the reset timeout period after V

CC

exceeds the device reset threshold or after the external manual reset is released. RESET

has an internal 5.5kΩ pullup resistor.

1

3

2

V

Supply Voltage and Input for Reset-Threshold Monitor

Ground

CC

3

GND

delay (t

). A manual-reset input shorter than 1.5μs

PBRST

Detailed Description

may release RESET without the 100ms minimum reset

timeout delay. To facilitate use with mechanical switches,

the MXD1813/MXD1818 contain internal debouncing

circuitry. A debounced waveform is shown in Figure 6.

RESET/RESET Output

A microprocessor’s (μP’s) reset input starts the micro-

processor in a known state. The MXD1810–MXD1813/

MXD1815–MXD1818 μP supervisory circuits assert reset

to prevent code-execution errors during power-up, power-

down, and brownout conditions (Figure 4). Whenever

Applications Information

Interfacing to μPs with Bidirectional

Reset Pins

V

CC

falls below the reset threshold, the reset output

asserts. Once V

exceeds the reset threshold, an

CC

Since the RESET output on the MXD1811/MXD1816

is open drain, these devices interface easily with μPs

that have bidirectional reset pins, such as the Motorola

68HC11. Connecting the μP supervisor’s RESET output

directly to the microcontroller’s (μC’s) RESET pin allows

either device to assert reset (Figure 7). No external pullup

resistor is required, as it is contained within the MXD1811/

MXD1816.

internal timer keeps the reset output asserted for the

specified reset timeout period (t ). Reset is also

RP

triggered by an externally initiated rising edge on the

RESET pin (MXD1813/MXD1818), following a low signal

of 1.5μs minimum duration.

Push-Button Reset (MXD1813/MXD1818)

Many μP-based products require push-button reset

capability (Figure 5), allowing the operator, a test

technician, or external logic circuitry to initiate reset.

On the MXD1813/MXD1818, a logic-low on RESET

held for greater than 1.5μs asserts a reset. RESET

deasserts following a 100ms minimum reset timeout

Negative-Going V

Transients

CC

In addition to issuing a reset to the μP during power-up,

power-down, and brownout conditions, these devices are

relatively immune to short-duration, negative-going V

transients (glitches).

CC

Maxim Integrated

│ 5

www.maximintegrated.com

MXD1810–MXD1813/

MXD1815–MXD1818

Low-Power μP Reset Circuits in 3-Pin

SC70/SOT23

Functional Diagram

MXD1810

MXD1812

MXD1815

MXD1817

MXD1811

MXD1816

V

CC

V

CC

RESET

GENERATOR

RESET

OR

RESET

GENERATOR

RESET

V

REF

V

REF

Figure 1. Functional Diagram, Push-Pull Output

Figure 2. Functional Diagram, Open-Drain Active-Low Output

The Typical Operating Characteristics show the Maximum

Transient Duration vs. Reset Threshold Overdrive for

which reset pulses are not generated. The graph shows

MXD1813

MXD1818

the maximum pulse width that a negative-going V

CC

transient may typically have without issuing a reset signal.

As the amplitude of the transient increases, the maximum

allowable pulse width decreases.

V

CC

MR

Ensuring a Valid Reset Output Down to

MONITOR

V

= 0

CC

When V

falls below the minimum operating voltage,

CC

RESET

GENERATOR

push-pull-structured reset sinking (or sourcing) capabili-

ties decrease dramatically. High-impedance CMOSlogic

inputs connected to the RESET/RESET pin can drift to

indeterminate voltages. This does not present a problem

in most cases, since most μPs and circuitry do not operate

V

REF

at V

below +1V. For MXD1810/MXD1815 applications

CC

where RESET must be valid down to V

= 0, adding

CC

a pulldown resistor between RESET and GND removes

stray leakage currents, holding RESET low (Figure 8).

The pulldown resistor value is not critical; 100kΩ is large

enough not to load RESET and small enough to pull

RESET low. For MXD1812/ MXD1817 applications where

Figure 3. Functional Diagram, Open-Drain Active-Low Output

with Manual Reset Detection

Maxim Integrated

│ 6

www.maximintegrated.com

MXD1810–MXD1813/

MXD1815–MXD1818

Low-Power μP Reset Circuits in 3-Pin

SC70/SOT23

V

CC

V

CC

TH

V

MXD1813

MXD1818

CC

t

RP

RESET

V

CC(MIN)

RESET

GND

MANUAL

t

RESET

RP

RESET

Figure 4. Power-Up Reset Timing Diagram

Figure 5. Push-Button Manual Reset

V

t

CC

PBRST

t

PBRST

(OPEN)

SWITCH BOUNCE

EXTERNAL

PUSH BUTTON

(CLOSED)

RESET

Figure 6. Manual Reset Timing Diagram

RESET must be valid to V

= 0, a 100kΩ pullup resistor

condition when the supply voltage drops below the

CC

between RESET and V

holds RESET high when V

minimum V , but will drift to a nonactive level due to

CC

falls below the minimum operating voltage (Figure 9).

the pullup resistor and the reduced sinking capability of

the open-drain output. Therefore, these devices are not

recommended for applications where the RESET pin is

The MXD1811/MXD1813/MXD1816/MXD1818 have

open-drain, active-low outputs with a pullup resistor

included internal to the devices. While using these

devices, RESET will most likely not maintain an active

required to be valid at V

= 0.

CC

Maxim Integrated

│ 7

www.maximintegrated.com

MXD1810–MXD1813/

MXD1815–MXD1818

Low-Power μP Reset Circuits in 3-Pin

SC70/SOT23

Table 1. Device Marking Codes

V

CC

TOP MARK

PART

SOT23

FZIV

SC70

AEK

AHU

AHT

AHW

AEL

AHV

AHY

AHX

AEM

AEN

AIA

V

CC

MXD1810_R46

MXD1810_R44

MXD1810_R41

MXD1811_R46

MXD1811_R44

MXD1811_R41

MXD1812_R46

MXD1812_R44

MXD1812_R41

MXD1813_R46

MXD1813_R44

MXD1813_R41

MXD1815_R31

MXD1815_R29

MXD1815_R26

MXD1815_R23

MXD1815_R22

MXD1816_R31

MXD1816_R29

MXD1816_R26

MXD1816_R23

MXD1816_R22

MXD1817_R31

MXD1817_R29

MXD1817_R26

MXD1817_R23

MXD1817_R22

MXD1818_R31

MXD1818_R29

MXD1818_R26

MXD1818_R23

MXD1818_R22

V

CC

FZKD

FZKC

FZKF

FZIW

FZKE

FZKH

FZKG

FZIX

MXD1811

MXD1816

µP

RESET

GND

Figure 7. Interfacing to Microprocessors with Bidirectional

Reset Pins

FZIY

FZKJ

FZKI

AHZ

AIE

FZKN

FZIZ

V

CC

AEO

AID

FZKM

FZKL

FZKK

FZKR

FZKQ

FZKP

FZKO

FZJA

FZJB

FZKV

FZKU

FZKT

FZKS

FZKY

FZKX

FZJC

FZKW

FZJE

V

CC

AIC

V

CC

AIB

MXD1810

AII

MXD1815

µP

RESET

AIH

AIG

AIF

GND

R

PULLDOWN*

GND

AEP

AEQ

AIM

AIL

*MXD1810/MXD1815 ONLY

Figure 8. Ensuring Valid RESET Output Down to V

(MXD1810/MXD1815 only)

= 0

CC

AIK

AIJ

AIP

V

CC

AIO

AER

AIN

V

CC

R

PULLUP*

AEV

V

CC

MXD1812

MXD1817

µP

RESET

GND

*MXD1812/MXD1817 ONLY

Figure 9. Ensuring Valid RESET Output Down to V

(MXD1812/MXD1817 only)

= 0

CC

Maxim Integrated

│ 8

www.maximintegrated.com

MXD1810–MXD1813/

MXD1815–MXD1818

Low-Power μP Reset Circuits in 3-Pin

SC70/SOT23

Selector Guide

OPEN-DRAIN

2.5V/3.0V/3.3V

SYSTEMS

PUSH-PULL

OPEN-DRAIN

PUSH-PULL

RESET

RESET WITH

PUSHBUTTON

DETECT

PART

5V SYSTEMS

RESET

MXD1810

MXD1811

MXD1812

MXD1813

MXD1815

MXD1816

MXD1817

MXD1818

—

✔

—

✔

—

✔

—

✔

—

✔

—

✔

—

✔

—

✔

—

✔

Ordering Information (continued)

Reset Threshold Table

†

PART

TEMP RANGE

-40°C to +105°C

PIN-PACKAGE

3 SOT23

3 SC70

SUFFIX

TYP. RESET

THRESHOLD (V)*

PART

(_ _)

46

44

41

31

29

26

23

22

MXD1811UR_ _-T

MXD1811XR_ _-T

MXD1812UR_ _-T

MXD1812XR_ _-T

MXD1813UR_ _-T

MXD1813XR_ _-T

MXD1815UR_ _-T

MXD1815XR_ _-T

MXD1816UR_ _-T

MXD1816XR_ _-T

MXD1817UR_ _-T

MXD1817XR_ _-T

MXD1818UR_ _-T

MXD1818XR_ _-T

MXD1810–MXD1813

MXD1815–MXD1818

4.62

4.37

4.12

3.06

2.88

2.55

2.31

2.18

3 SOT23

3 SC70

3 SOT23

3 SC70

3 SOT23

3 SC70

3 SOT23

3 SC70

*Factory-trimmed reset thresholds are nominally ±1.5% at

room temperature.

3 SOT23

3 SC70

Chip Information

3 SOT23

3 SC70

PROCESS TECHNOLOGY: BiCMOS

†The MXD1810–MXD1813/MXD1815–MXD1818 are available

with factory-set V reset thresholds from +2.18V to +3.06V

CC

Package Information

(MXD1815–MXD1818) and +4.12V to +4.62V (MXD1810–

MXD1813). Choose the desired reset-threshold suffix from the

Reset Threshold Table and insert it in place of the “_ _”

following “R” in the part number. All devices are available in

tape-and-reel only in 2500 unit increments. Other threshold

voltages may be available. Contact factory for availability.

For the latest package outline information and land patterns

(footprints), go to www.maximintegrated.com/packages. Note

that a “+”, “#”, or “-” in the package code indicates RoHS status

only. Package drawings may show a different suffix character, but

the drawing pertains to the package regardless of RoHS status.

Devices are available in both leaded and lead(Pb)-free

packaging. Specify lead-free by replacing “-T” with “+T”

when ordering.

PACKAGE

TYPE

PACKAGE OUTLINE

CODE

LAND

PATTERN NO.

NO.

3 SC70

X3-2

21-0075

21-0051

90-0208

90-0179

3 SOT23

U3-1

Maxim Integrated

│ 9

www.maximintegrated.com

MXD1810–MXD1813/

MXD1815–MXD1818

Low-Power μP Reset Circuits in 3-Pin

SC70/SOT23

Revision History

REVISION

NUMBER

REVISION

DATE

PAGES

CHANGED

DESCRIPTION

1

12/05

11/14

Miscellaneous updates

1,9-11

No /V OPN in Ordering Information, removed automotive reference from

Applications section; updated Packaging Information

2

1, 10, 11

For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.

Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses

are implied. Maxim Integrated reserves the right to change the circuitry and speciﬁcations without notice at any time. The parametric values (min and max limits)

shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.

©

Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.

2014 Maxim Integrated Products, Inc.

│ 10

型号:	MXD1818UR26+
是否无铅：	不含铅
是否Rohs认证：	符合
生命周期：	Active
包装说明：	,
Reach Compliance Code：	compliant
Factory Lead Time：	6 weeks
风险等级：	1.64
模拟集成电路 - 其他类型：	POWER SUPPLY SUPPORT CIRCUIT
JESD-609代码：	e3
端子面层：	Matte Tin (Sn)
Base Number Matches：	1

电子百科

产品导航

产品型号MXD1818UR26+T的Datasheet PDF文件预览

MXD1818UR26+相关产品..

MXD1818UR26+相关文章

IC37:专业IC行业平台